CIPDB › China Industry › Industrial Equipment & Components › Drone & UAV & Accessories
Bls-50A 4 in 1 ESC 2-6s Fpv Drone Flight Controller Stack for RC Aircraft1
Drone UAV AccessoriesStackFlight Control
Padi Fly Technology Co., Ltd
Preview:
Product Description Padi Fly main business includes UAV detector module, handheld detection, backpack detection, vehicle detection, UAV accessories, etc. Product DescriptionBLS-50A 4 in 1 ESC Flight Controller Features:1. Built with the firm STM MCU, ICM42688 and large motor pads which makes you can solder up your motors easily and brings a smooth flight experience.2. Equipped with some pads to support soldering up the LED strip and GPS. After you solder up them, you can fly your model at night and check where is it, which is very convenience.3. The mounting size is 30.5 x 30.5mm and the hole diameter is 4mm, which is suitable for most models in the market. You can according to it choose whether it is fit your models or not.4. Built-in type-c socket, you can connect the flight controller stack with your computer to change the data that you want. The firmware is Betaflight Configurator and INAV. BLS-50A 4 in 1 ESC Flight Controller Stack:ICMICM42688USB Port TypeType-CBarometerBMP280OSD ChipBetaFlight OSD w/ AT7456E chipDJI Air Unit Connection WayTwo ways supported: 6-pin connector or direct6-pin DJI PlugSupported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.Black box16M Black BoxCurrent Sensor InputSupported. For 60A ESC, please set scale = 180 and Offset = 0.Power Input3S - 6S Lipo(Through ESC 8-PIN connector)5V BEC Output5 grous 5V output,the total current load is 3A9V Output3 groups 9V output,the total current load is 2.5A3.3V Output1 group 3.3V output,maxmum current is 300mAESC SignalM1 - M4UART6 sets(UART2 UART5, UART3), UART6(Dedicated for SBUS), UART4(Dedicated for ESC telemetry), UART1 (Dedicated for VTX data setting)SbsDebugging to UART6 ChannelESC TelemetryUART R4(UART4)I2CSupported. SDA & SCL pads on front side. Used for magnetometer.LED PadSupported. LED,5V, and GND pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.Buzzersupported,5V,BZ pads for 5V BuzzerBOOT ButtonSupported.Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.Supported Flight Controller FirmwareBetaFlight(Default),Firmware Target NameSTM32F405Mounting30.5 x 30.5mm( 4mm hole diameter)Dimension37(L) x 37(W) x 6.6(H)mmWeight7.5gBLS 60A 4-in-1 ESC:size41 * 39 * 5mmContinuous Current60A * 4Burst Current70A(10seconds)TVS Protective diodeYesExternal Capacitor ESC ProtocolDSHOT300/600Power Input3-6S LiPoPower OutputVBATCurrent Sensor35V1000uF Low ESR Capacitor(In the package)Support (Scale=180 Offset=0)ESC TelemetryNot supportedMounting30.5 x 30.5mm( 4mm hole diameter)Dimension42.3(L) * 37(W) * 6.2mm(H)Weight12g BLS 50A 4-in-1 ESC:size41*39*5mmAperture30.5 * 30.5mmFirmwareBLHELI-S J_H_30_REV16_7Weight15gContinuous current50AMaximum current60A (10 seconds)ProcessorEF8BB21Drive signal supportDShot150-300-600/Multishot/Oneshot/PMWCurrent sensorsupports Detailed PhotosCompany ProfilePadi Fly Technology Co. Ltd specializes in the field of advanced technology.Our company is located in the vibrantcity of Shenzhen,known as a hub of innovation andtechnology in China.With over 3000 square meters of plant space, we specialize in the design, development, and distribution of FPV drones along with drone countermeasure solution. We are known for our innovation, quality, and commitment to enhancing the user experience.Our Business Range for FPV drone accessories:We can provide include: Image transmission, motor, carbon fiber frame, flight control, electrical regulation, antenna, remote control, propeller, charger, etc..We also provide the industry's professional OEM and ODM technology and services.Packaging & Shipping FAQ Q:Why choose PDFLY?A:1. From real factory: cheaper price, better quality, faster delivery.2. Quality assurance: Ship after successful testing.3. After-sales: Professional team to solve problems and technical support. Q:How can we guarantee quality?A:1.Always a pre-production sample before mass production;2.Always final Inspection before shipment;3.Professional sales staff will communicate with you to confirm every link Q:What's the lead time?A:Sample needs 3-7 days, mass production needs 7-10 days, according to your order requirements & volumes. Q:How to place an order from you?A:Please send the products you like to us and our professional sales will contact with you within 24 hours to confirm the details of the products and negotiate. After you confirm the order, we will guide you through payment and arrange delivery, tell you the tracking number and help track the logistics. We look forward to your comments on our products and services.
Purchasing Agent
Note: Send your message to supplier or manufacturer.
Welcome to our Professional and comprehensive procurement services...