CIPDB › China Industry › Metallurgy, Mineral & Energy › Graphite & Products
Industrial Graphite Electrode UHP/HP/RP Dia 500mm for Steel Making Include Graphite Anodes /Cathodes Electrode for High-Power Thermal System1
Graphite ProductsIndustrial ElectrodeGraphite Electrode
Qingdao TTWY International Trade Co., Ltd.
Preview:
Product Description Product DescriptionGraphite-Products Artificial Graphite Electrode UHP/HP/RP Dia 500mm for Steel Making Include Graphite Anodes and Cathodes for High-power Thermal SystemGraphite Electrodes are a high temperature resistant graphite conductive refractory material used in the metallurgical industry. Graphite Electrodes are made of petroleum coke, bituminous coke as aggregates, coal tar pitch as binders, after raw material calcination, crushing and milling, batching, kneading, molding, roasting, impregnation, graphitization and machining, which are also known as artificial graphite electrodes in order to distinguish from natural graphite electrodes made of natural graphite.Notice : How to Use Graphite Electrode> Be careful when transporting and pilling electrodes with forklift and avoid of collision. One layer of goods at a time; notice the balance and alignment and avoid falling or breakage.> When loading and unloading with forklift, wire rope must be used and steel wrapping tape cannot be employed directly to fetch electrodes.> Electrode should be stored in clean and dry place. When pilling up outdoors, it should be covered with rain-proof tarpaulin and the number of piling layers ought not to exceed four.> When using electrodes, special tools should be employed to cut the steel wrapping tape, and crane should not be adopted to avoid bursting.> Steel-wire ball, metallic brush or emery cloth is not allowed for cleaning the electrode thread, but compressed air free of oil and water is available.> Use revolved resilient hanger and put soft truss pad under the electrode joint to avoid breakage of the thread.> Lift the electrode to the furnace by using a hoister with resilient hangers, and find out the center and move slowly downwards, screw and tight with a hoop.> If the two poles of the two electrodes are untouched or touched in overpressure, this may cause bad effect.> In order to avoid electrode breakage, put the large materials in lower part and small materials in the upper part. Specifications for RP, HP, UHP graphite electrodes with nipples RPHPUHPElectrode:Bulk Density≥ 1.56g/cm3 Specific Resistivity≤ 8.5μm Bending Strength≥ 10.0MPa Elastic Modulus≤ 9.3GPaThermal Expansion Coefficient≤ 2.7x10 -6/°CAsh≤ 0.5% Nipple:Bulk Density≥ 1.68g/cm3 Specific Resistivity≤ 7.0μm Bending Strength≥ 14.0MPaElastic Modulus≤ 13.7GPaThermal Expansion Coefficient≤ 2.5 x10 -6/°CAsh≤ 0.5%Electrode:Bulk Density≥ 1.65g/cm3 Specific Resistivity≤ 6.5μm Bending Strength≥ 12.0MPa Elastic Modulus≤ 10.0GPaThermal Expansion Coefficient≤ 2.2x10 -6/°CAsh≤ 0.3% Nipple:Bulk Density≥ 1.74g/cm3 Specific Resistivity≤ 5.5μm Bending Strength≥ 16.0MPaElastic Modulus≤ 14.0GPaThermal Expansion Coefficient≤ 2.0 x10 -6/°CAsh≤ 0.3%Electrode:Bulk Density≥ 1.68g/cm3 Specific Resistivity≤ 5.8μm Bending Strength≥ 16.0MPa Elastic Modulus≤ 14.0GPaThermal Expansion Coefficient≤ 1.9x10 -6/°CAsh≤ 0.2% Nipple:Bulk Density≥ 1.76g/cm3 Specific Resistivity≤ 4.5μm Bending Strength≥ 18.0MPaElastic Modulus≤ 16.0GPaThermal Expansion Coefficient≤ 1.4 x10 -6/°CAsh≤ 0.2% Actual diametersActual lengthsMmMmMAXMINRough spotLengthToleranceShot Ruler size20082042011981600±100-2752501025625224816001800300123073032993501435735334740016409404400160018002000 45018460455451500205115065026002461360760478031.2782776774200022002400±100-4008003280279679487034.88728668629003690289689292036.892291691296038.4962956952102040.8102210161012 220026002800106042.4106210561052110044110210921092114645.8114811401138119747.9119911911189125050125212441242127250.9127412661264130554.4130712991297132152.8132313151313140056140213941392FAQQ1:Where can I get product and price information?A1:Send us inquiry email, we will contact with you, once we receive your email, or contact me on WhatsApp, Linkedin, Skype and WeChat. Q2: What's the payment terms?A2: 30% of the payment should be paid in advance, and the balance should be paid on seeing the scan copy of BL; L/C is also welcomed. Q3: How to deliver the goods?A3: We deliver the goods by truck to the port, or loading in containers in our factory. Q4: What's the minimum order quantity?A5: 18-20tons, one 20 fcl. Q4: What's the delivery time?A6: 2-3 weeks after got the deposit.
Purchasing Agent
Note: Send your message to supplier or manufacturer.
Welcome to our Professional and comprehensive procurement services...