IPDB › China Industry › Manufacturing & Processing Machinery › Assembly Line & Production Line
Complete Alpha Gypsum Powder Production Lines for Mass Production1
Assembly Line Production Line, Gypsum Powder Machine, Gypsum Alpha Powder Machine, Gypsum Alpha Powder Calcination Machine
Yurui (Shandong) Machinery Co., Ltd.
Preview:
Product Description Product Description Alpha High-Strength Gypsum Powder Project- Production technology introduction This process adopts the high-pressure aqueous solution method. The principle is to add desulfurized gypsum into an aqueous solution containing a crystal modifier to make a suspension. Then, the suspension is pressurized and heated while being continuously stirred. After that, through clarification, filtration, drying, and grinding, the product can be obtained.1. Premixing of the slurry The desulfurized gypsum is metered, and water and other additives are metered separately. Then, they are sent into the mixing tank through the slurry - making and conveying system with stirring. At the same time, water is added to the mixing tank to mix with the gypsum, so that the mass concentration of the slurry reaches 1250 - 1350 g/L, and the concentration can be increased to 1450 g/L. Meanwhile, the slurry is heated to reach the temperature required by the process (60 -90°C).2. First crystal transformation 1.1Crystal transformer according to the process steps for crystallization.1.2 Initial crystallization - First, a certain amount of hot water is added to the No. 1 reactor, and then the given slurry and additive A are added. The crystal transformation starts at about 120°C and an absolute pressure of 0.3 -0.4 MPa. At the same time, samples are taken every 10 - 20 minutes and observed under a microscope to check the formation of crystal shapes.1.3 Recrystallization - The functional additive B and the slurry are fed into the No. 1 reactor together according to the given values. If the crystals are all needle - shaped, the main reasons are that the addition coefficient of additive B is too low and the temperature difference is too large. Basic technological process and steps1.4 Repair of crystallization - The slurry is added to the No. 1 reactor until the slurry level reaches about 90% of its volume. The proportion of the admixture is adjusted, and the reaction temperature is controlled at 110 - 130°C and the pressure at 0.3 -0.4 MPa to repair the recrystallized gypsum crystals. Samples are taken for observation. When about 98% of the dihydrate gypsum crystals are transformed into regular hemihyd rate gypsum crystals, the slurry is pumped into the No. 2 reactor.3. Second crystal transformation The second crystal transformation is carried out in the secondary crystal transformer. The temperature is controlled at 120 -130°C, the pressure at 0.3 - 0.4 MPa, and the reaction time is stabilized at 0.5 h. When it is found that there are basically no fine and irregular particles, the product is basically α - gypsum.4. Crystal separation The well crystallized gypsum slurry discharged from the No. 2 reactor enters the centrifuge along the pipeline at a set conveying speed.Under the high - speed rotation of the centrifuge, most of the water in the gypsum slurry is removed under the action of a certain temperature and hot air, and then it enters the next process.5. Drying The hemihydrate gypsum crystals from the centrifuge enter the dryer. The temperature in the front area of the dryer is 180 -230°C, the discharge temperature is 75 - 105°C, and the frequency of the dryer is 10 - 50 Hz. Dried under the action of thestirring shaft, the hemihydrate gypsum crystals are turned into dry pure α - gypsum crystals and discharged. Product Parameters Paramater of Gypsum Powder Machine line Product Name Gypsum Alpha Powder Production lineAnnual capacity 5,000 tons per yearWorking time 24h/day ,300day/yearRaw Material Gypsum Type Natural dihydrate gypsum---CaSO4 ·2H2O ≥90%Desulfurized gypsum--- CaSO4 ·2H2O ≥90%Phosphogypsum ----CaSO4 ·2H2O ≥90%Gypsum powder Mesh Within 220 meshesHeating method Pressurized steam method (horizontal kettle autoclave)Pressurized aqueous solution method (liquid phase method)Application of the powder Ceramic molds, gypsumPrecision casting moldsCrafts and artsGRG productsGypsum self-levelingDental moldsDegree of automation Fully automaticFinal product specification Gypsum powderFuel for the heating system natural gas,coal,diesel,heavy oil,light oil etcFinished powder strength High-strength gypsum compressive strength ≥25-50 MPA,Ultra-high-strength gypsum compressive strength ≥ 50 MPA. Application Company ProfileWhat we provide is not ONLY the machine BUT the whole system. Yurui (Shandong) Machinery Co., Ltd, is an enterprise integrating gypsum projects R&D, design, Manufacturing, exportation, installation, and commissioning. We have been deeply engaged in the field since 1998, setting up 100+gypsum projects domestic and abroad. Our engineers group who only serve for YURUI left a full footprintover Africa, Asia, and south America, total of 20+countries. We hold different projects in each area, offering case visiting on-site. Besides we developed online visiting which breaks the limit of the virus. 1.We are not a machinery provider, but an overall solution provider. 2.We focus on the demands of users, never stop updating, improving, and surpassing. 3.We pursue extreme cost performance, not only price. Packaging & Shipping 1.Customized Packaging Solutions2.Heavy-Duty Securing &Reinforcement3.Rust & Moisture Protection4.Shock & Impact Resistance5.Professional Loading & Container Optimization6.Comprehensive Shipping Documentation & SupportWith our expert packaging and logistics solutions, you can be confident that your machinery will arrive safely, securely, and in excellent condition. Let us handle the complexities of international shipping while you focus on growing your business! After Sales Service 1. About Production:We have our own factory. Greater control and flexibility in production. We are able to make independentdecisions on all aspects of production. Respond to emergencies and special needs.2. About Accessories:We provide free accessories for one year. About Raw Materials: We provide our customers with advanced raw material formulation and supply.3. About Installation:Specialized engineering teams are responsible for designing foundations, installing equipment and maintaining it.4. About our service team:A professional service team takes care of the entire project process: project evaluation, manufacturing, export, transportation and commissioning as well as long-term after-sales service support.
Purchasing Agent
Note: Send your message to supplier or manufacturer.
Welcome to our Professional and comprehensive procurement services...
Message:
OK ! We suggest you detail your product requirements and company information here.
Enter between 20 to 4,000 characters.
Your inquiry content must be between 20 to 4000 characters.