IPDB › China Industry › Industrial Equipment & Components › Bearing
Solid Grease Bearing Say Goodbye to Frequent Lubrication 23152cc/W64 23152/L11 23152/Lp03 23152/D137lso Solid Grease Bearing1
Other Bearing, Solid Grease Bearing, 22252cc/W64
Suzhou Dsn Bearings Limited
Preview:
Product Description The DSNstandard assortment of bearings and bearing units with Solid Oil (fig. 1) includes:Deep groove ball bearingsSpherical roller bearingsAngular contact ball bearingsCylindrical roller bearingsSelf-aligning ball bearingsInsert bearings and ball bearing unitsTapered roller bearingsOn request, DSNcan supply other bearing types with Solid Oil to meet the needs of a particular application, except for CARB toroidal roller bearings which are unsuitable for use with Solid Oil. Bearings fitted with a large-volume cage are not suitable for Solid Oil because there is too little free space inside the bearing.Solid Oil variantsStandard variant (designation suffix W64, table 1)Contains a high-quality synthetic oilMeets the needs of most applicationsFood grade variant (designation suffix W64F, table 1)Contains an oil registered by as a category H1Meets the needs of food applicationsLow temperature variant (designation suffix W64L, table 1)Contains an oil with low viscosityMeets the needs for low temperature applicationsSealed bearingsWith integral contact seals are strongly recommended in wet environmentsWith Solid Oil increase the sealing effectiveness, as the Solid Oil supports the seals axially, preventing them from deflecting and opening under pressureFor information about sealing options, contact the DSNapplication engineering service.Where carbon steel bearings are exposed to wet environments, additional external seals are recommended to protect the bearing's external surfaces from corrosion.General bearing specificationsDimension standards, tolerances, internal clearanceRefer to General bearing (unit) specifications in the relevant product section of the standard bearing (unit).LoadsLoad carrying capacityThe basic dynamic and static load ratings for bearings with Solid Oil are the same as for corresponding DSNstandard bearings.Temperature limitsThe permissible operating temperature for bearings with Solid Oil can be limited by:The dimensional stability of the bearing rings and rolling elementsThe cage(s)The sealsThe Solid OilFor limits of bearing rings, rolling elements, cage(s) and seals, refer to Temperature limits of the relevant product section of the standard bearing.The relevant limits for Solid Oil are listed in table 1.Where temperatures outside the permissible range are expected, contact Speed limitsThe recommended speed values for bearings and bearing units with Solid Oil (table 2), operating in an ambient temperature of 20 °C (70 °F), are limited by the maximum continuous operating temperature of 85 °C (185 °F). Ambient temperature is the temperature closest to the bearing position, not necessarily room temperature.For bearing types or variants not listed in table 2, contact the DSNapplication engineering service.For ambient temperatures above 20 °C (70 °F), the speed limit should be reduced using the reduction factor fT (diagram 1).Calculation exampleA deep groove ball bearing 6208/W64 is to operate at an ambient temperature of 50 °C (120 °F). What is the reduced speed limit?Recommended speed limit for 20 °C (70 °F) ambient temperatureFrom table 2: speed value ndm = 300 000 mm/min (single row deep groove ball bearing with a stamped metal cage)Dimensions: d = 40 mm, D = 80 mmn = 300 000 / dm = 300 000 / (0,5 (40 + 80)) = 5 000 r/minReduction for 50 °C (120 °F) ambient temperatureFrom diagram 1: speed reduction factor fT ≈ 0,53nreduced = 5 000 fT = 5 000 x 0,53 = 2 650 r/minFriction characteristicsThe friction characteristics of a bearing with Solid Oil correspond to the relevant DSNstandard bearing except that the Solid Oil polymer filling adds a fixed friction.MountingIf a bearing with Solid Oil is to be hot mounted, it should be heated to a maximum of 120 °C (250 °F) by using an induction heater.Heating plates or heated oil baths should not be used.Designation systemRefer to Designation system in the relevant product section of the standard bearing/unit.The designation suffixes used to identify bearings with Solid Oil are explained in the following:W64 Synthetic base oil type, standard variantW64F Synthetic base oil type, H1 approved for food applicationsW64L Synthetic base oil type, designed for low temperature applications
Purchasing Agent
Note: Send your message to supplier or manufacturer.
Welcome to our Professional and comprehensive procurement services...
Message:
OK ! We suggest you detail your product requirements and company information here.
Enter between 20 to 4,000 characters.
Your inquiry content must be between 20 to 4000 characters.