IPDB › China Industry › Manufacturing & Processing Machinery › Machine Tools
Punch Presses Machine with 160tons, 250tons and 400tons1
Machine Tools, Punching Machine, 250tons and 400tons, Press, Punch
Nanjing BHT Intelligent Equipment Co., Ltd.
Preview:
Product Description Product Description1. Type /Name/QuantityTypeNameQuantity (P)RemarksJH21-125TC-frame Fixed Bolster Press 2. Energy and environmental requirementsProjectUnitSupplier RequirementRemarksPowerGrid form-TN-S Supply voltageAC380V±7% Frequency-50HZ±0.5HZ EnvironmentAmbient temperatureoC-5oC~40oC Ambient humidity-50%(+40oC)~90%(+20oC) WorkshopThe height m of the crane trackmmust meet the machine installation requirements Crane modelton Logistics door sizm The conditions of the required plant must meet the requirements provided by the supplier in this form. 3. Equipment implementation standardsGB 5226.1-2008Mechanical and electrical safety, Part 1 of Mechanical and electrical equipment:General technical conditionsJB/T6580.1-2014C-frame Fixed Bolster Press, Part 1:Technical conditionsGB 17120-2012Forging machinery, Safety technical conditionsGB/T7932-2017General rules and safety requirements for pneumatics on systems and their componentsGB/T7935-2005Components of hydralic General technical conditionsGB/T 10923-2009Forging machinery, Accuracy Test General RulesGB 26483-2011Mechanical press, limit of noise 4. Machine4.1 Main SpecificationsSpecificationsUnitJH21-25JH21-45JH21-60JH21-80JH21-100JH21-125JH21-160JH21-200JH21-250JH21-315JH21-400Type HSHSHSHSHSHSHSHSHSHSHSNominal forceKN2504506008001000125016002000250031504000Nominal Strokemm33444455556666666.56.57788Slide Strokemm50807012080140100160100160110180130200150200160220160220180250Slide Strokes Per MinuteFixedmin-11251009580907080608055705060455045453045304030Variable75-15060-12065-11550-9560-11045-8555-9540-7555-9535-6550-8535-6040-7030-5535-6030-5530-5520-3530-5520-3530-5020-35Maximum Die Set Heightmm265250295270330300350320365335385350435400485450530500530500585550Die Height Adjustmentmm506070809090100110120120120Between slide center and frame mm210225270310330350400430450450490Columns Distancemm4505155606106706707369109809801050Bottom size of slideL×Rmm3604004805406206207008809509501020F×Bmm250340400460520520580650700700750Shank Hole SizeDiamm4050505070707070707070Depthmm506070708080100100130130140Bolster sizeL×Rmm7208259309501060110011751390150015401700F×Bmm400440520600640680760840880880950Blanking Hole Diametermm150150150180180200220240240240240Bolster Thicknessmm80110130140145155165180190190210Bolster Surface Heightmm7808009009009009009001000100010001100Overall DimensionsF×Bmm15001585154017652000204023052600266027202850L×Rmm9451075120012001300132014201540164016801750Hmm21202390257027253010303532153800385038504140Distance Between Foundation BoltsF×Bmm9801075110012101365143016652020210021402185L×Rmm6907608409201020104011401360146015001570MotorPowerKw35.55.57.57.5111518.5223037Weight(Approximate)Kg2450355051506450865095501360019200232002660029500Press PressureMpa0.54.2 Main PartsNoName of PartManufacturerMark1Hydraulic Overload ProtectorShowa /Sterlon/KingAir 2Double solenoid valveTOYOOKI/TACO/ ROSS 3Rolling bearingHRB/ ZWZ / LYC 4PLCSchneider / Omron 5CamDomestic famous brand 6Touch ScteenKinco 7InverterSinee/VeichiOptional8EncoderEltra 9Pressure SwitchARK/SHANJIANG 10Main circuit breakerSPX/CHNT 11AC contactorSchneider 12Three-pole circuit breakerSchneider 13Single pole circuit breakerCHNT 14RelayIDEC 15Light CurtainDomestic famous brandOptional16Main MotorSiemens/Huali 17Switch buttonDomestic famous brand 18DC power supplyOmron 19TransformerDomestic famous brand 20Proximity switchOmron 4.3 Main Component Structure4.3.1 The machine body adopts a box-shaped structure welded with steel plates, adopts CO2 gas shielded welding, and performs stress relief treatment by tempering. It has high strength and rigidity and high geometric accuracy and stability.4.3.2 The processing of the fuselage is completed on the Italian PAMA boring and milling machining center, and the clamping is performed once to ensure the accuracy of the machine's shape and position.4.3.3 The main transmission form: crankshaft connecting rod structure, the crankshaft is vertically arranged with a short fulcrum distance, and the structure is compact.4.3.4 Drive mode: high torque wet clutch.4.3.5 Drive system: motor-belt-gear pair.4.3.6 Transmission gear:Straight tooth gear, oil-immersed lubrication, has the advantages of high meshing accuracy, smooth transmission, low noise, and large carrying capacity.4.3.7 Copper tiles and bearings:The copper tiles and bearings of important parts have reliable lubrication guarantee. Connecting rod copper tile, crankshaft supporting copper tile mining are high ratio copper tile.4.3.8 Clutch / brake (wet type):4.3.8.1 The control system adopts imported double solenoid valve, which is sensitive and reliable.4.3.8.2 High-torque wet clutch has the characteristics of low inertia, high torque, no pollution and low noise. It meets environmental protection requirements, has a long life and low maintenance cost.4.3.8.3 The main motor adopts single-speed motor + inverter (optional) speed regulation mode, with short circuit protection and current overload protection.4.3.8.4 In order to prevent the second start of the machine tool and protect the personal safety of the operator, a proximity switch to prevent the second start is provided to prevent the slider from repeating the movement and play a protective role.4.3.9 Slide and guide rail:4.3.9.1 The slider adopts an extended six-sided guide rail, and the lubricated guide plate is a composite material, which has high guide accuracy and good wear resistance.4.3.9.2 The slider is equipped with a hydraulic overload protection device. An overload unloading alarm is generated when the rated tonnage is exceeded by about 10%. The slider automatically stops. After overload, it needs to jog back to the top dead center and the hydraulic overload device automatically compensates for pressure.4.3.9.3 The operating angle of the crankshaft is displayed electronically and placed on the control panel. (JH21-25 ~ 80 are mechanical pointer type)4.3.9.4 The slider is equipped with a motorized height adjustment device: (JH21-60 and above models are electric, and JH21-25 ~ 45 are manual)(1) The upper and lower limit positions are automatically stopped;(2) During adjustment, the height of the die is displayed in the instrument with a display accuracy of 0.1mm.4.3.10 Balancer: Air type, balance pressure is manually adjusted and set.4.3.11 Fuselage:4.3.11.1 Equipped with a fixed two-handed button station 1 / set.4.3.11.2 Has the air source pressure gauge.4.3.12 Hydraulic, lubricating and pneumatic parts:4.3.12.1 Pump uses imported or domestic high-quality components.4.3.12.2 Centralized concentrated oil forced lubrication system (1) Lubrication parts: bearings, guide rails, copper tiles, etc. (2) The lubricating distributor is selected from standard imported or domestic high-quality products.4.3.12.3 Intermittent quantitative manual lubrication system (1) Lubrication parts: balancer4.3.12.4 The overload pump provides oil for the overload protection of the slider, and the inner surface of the oil tank is degreased and pickled.4.3.12.5 Compressed air is used for clutch / brake, balance cylinder, slider overload protection and blowing device.4.3.12.6 The main air pressure is provided with a pressure detection switch, which is interlocked with the host.4.3.12.7 There is a water separation filter at the inlet of the air source to prevent excessive moisture from entering the pipeline.4.3.12.8 All system pipelines and components are designed to be in order, arranged in an orderly manner, without leakage, and are easy to disassemble and maintain.4.3.12.9 The clutch gas tank and the balancer gas tank all meet safety standards, so that the air pressure fluctuates within 20%. Pneumatic equipment meets general technical requirements.4.4 Electrical part4.4.1 Main operation panel: color touch screen, main motor running indicator4.4.2 Electrical cabinet: Use wall-mounted electrical box.4.4.3 Control device: a. With continuous, single, and inching working modes for selectionb. Adopt multi-screen touch screen to realize the main process parameters and fault indication of the press, mainly including the following basic information:Production process status monitoring and production volume presetting and countinMachine status display, I / O status monitoring.Fault display diagnosis function and fault location;Yield counter (displayed on the touch screen);4.4.4 General technical requirementsa. Voltage rating and protective measuresb. Main power supply: 380V ± 7% 50HZ ± 0.5HZ (three-phase five-wire, 3P + PE + N), with standard grounding design in the distribution box, used for three-phase five-wire incoming power supply; the main switch has overload and Electromagnetic protection function.c. Auxiliary power supply:The independent auxiliary power supply with safety device is used for lights and switch units, not for production line equipment; the independent power supply is for the production line PLC-CPU, and all HMI and PLC-CPU power supplies require switches and control units. The power supply of PLC and solenoid valve is designed according to the product. All the connection circuits with PLC follow the grounding standard after isolation transformer.4.4.5 Auxiliary devices and others:4.4.5.1 The operation of the press is controlled by two hands.4.4.5.2 When the power supply is cut off or the equipment is in an emergency stop, in order to avoid equipment damage or personal injury, no movement of the equipment is allowed.4.4.5.3 The number of external detection signals and the number of manual operation buttons can ensure that the equipment has perfect protection functions, ensure that the equipment is easy to operate and reliable.4.4.5.4 The button station is operated by both hands, and the emergency stop button is set on the button station of the press, and marked with a bold red.Oil-proof, dust-proof and shock-proof4.4.5.5 Lighting equipment:Mold area lighting: illumination above 150LXThe illuminator is shock-proof, oil-proof and dust-proof4.4.6 The electrical control system of the press meets the requirements of GB5226.1-2008 "Mechanical Safety, Mechanical and Electrical Equipment Part I General Technical Conditions"Detailed Photos Processing and ManufacturingCNC Machining Center from DOOSAN Korea & PAMA ItalyGear hobbing machine from Germany Gleason & LiebherrCNC Machining Center TOSHIBA JapanBoring and milling machining center from PAMA ItalyPentahedral machining center from Hitachi JapanLarge tempering furnace Packaging & ShippingSteel Pallet with Waterproof Cloth & Strong Wooden packaging Certifications BHT WORLD Clients BHT WORLD have exported the products to 65 countries (Germany, Sweden, Hungary, Italy, Netherlands, Spain, Portugal, Czech Republic, Lithuania, Serbia, Greece, Malta, Austria, Kosovo, Turkey, Ukraine, Albania, Estonia, Belarus, Bulgaria, Bosnia, Croatia, Romania,USA, Brazil, Argentina, Mexico, Bolivia, Colombia, Canada, Peru, Chile, Australia, New Zealand, Rwanda, Egypt, South Africa, Tanzania, Nigeria, Botswana, Mauritius, Russia, Vietnam, India, Iran, Singapore, Uzbekistan, Thailand, Sri Lanka, Bangladesh, Malaysia, Kazakhstan, Philippines, Bahrain, Pakistan, United Arab Emirates, Kuwait, Saudi Arabia, Sudan, Jordan, Oman, Qatar, Syria, Israel, Yemen)
Purchasing Agent
Note: Send your message to supplier or manufacturer.
Welcome to our Professional and comprehensive procurement services...
Message:
OK ! We suggest you detail your product requirements and company information here.
Enter between 20 to 4,000 characters.
Your inquiry content must be between 20 to 4000 characters.