IPDB › China Industry › Tools & Hardware › Building Hardware
Vertical Potable Welded Expansion Vessel for Domestic Water Systems1
Building Hardware, Plumbing Hardware, Expansion Vessels, Pressure Vessels
Taizhou Tianyang Electrical Co., Ltd.
Preview:
Product Description Vertical Potable Welded Expansion Vessel for Domestic Water SystemsProduct DescriptionImportant NotesAThe replacement membrane for most of the conventional 80-100 liter membrane pressure vessels, for use in sanitary cold-/hot water systems, domestic waterworks, solar- and pressure maintenance systems and garden pumps. The membrane is made of EPDM rubber, and therefore suitable for drinking water.Ethylene-Propylene-Diene-Monomer Rubber:This EPDM rubber belongs to the group of elastomers. This synthetic material is characterized by resistance to hot air, weathering and ozone. The elastomer shows low gas permeability, good resistance to chemicals as well as up to 100°C very good noise and shock energy absorption qualities. In the low temperature range the butyl rubber remains elastic up to -70°C.It is mainly used for air hoses and inner cores of tyres, bladders, steam hoses and linings for tanks. Further fields of application are foils, membranes, unvulcanized sealants and bands.This EPDM rubber is allowed as chewable mass for chewing gum according to Annex 4 on Additive Admission Regulation. Consequently, the material is harmless for drinking water installations.BReplacement 100L Pressure Vessel for use in sanitary cold-/hot water systems, suitable for nearly all domestic waterworks, solar- and pressure maintenance systems and garden pumps. This pressure vessel will be delivered with included. EPDM membrane and has a 100L capacity. The vessel is designed for a maximum pressure of 10 bar (16/20/25/30/35 Bar Also available,please contact Mr.Tom Lee for details)and will be delivered in a horizontal position. The tank is checked for tightness with up to 5,4 bar water pressure by the producer.It has a 1inch (32,89-33,25mm) pump connector.The pressure vessel has additionally an integrated valve for inflating the space betwen tank and membrane.This vessel series is welded of qualitative steel sheet, according to UNI-EN-standards and is equipped with a heat- and age resistant EPDM-membrane.CAbout the primary pressure in the pressure vessel:The primary pressure should be set approximately 0,1-0,2 bar lower than the switch-on pressure of the pump and has to be checked at regular intervals. Any failure of observance may cause damage on the EPDM-diaphragm of the pressure vessel. A more accurate calculation results from the pump′s switch-on pressure x 0,9. Example: Switch-on pressure on the pressure switch of the domestic waterworks is set to 1,5bar: 1,5bar x 0,9 = 1,3-1,4 barImportant: The vessel′s pressure should only be inflated or deflated when the pressure to the water system has been released before. Attention: It is absolutely necessary to have released the air and water pressure before the opening of the pressure vessel !For more models of expansion vessels ,please refer to PhotoModelWarrantyVessel Capacity Unit Price Connection HeightLengthMax. operating pressure Standard Precharge PressureMax. operating temperature Unit Package DimensionXMonthsLiterUS Dollar InchmmmmBarBar°C mmTY-08-2L-10362Come On,Please Contact US For Best Offer (Export Only)3/4''13023060.970150x150x240TY-08-5L-103653/4''205240101.5100210x210x250TY-08-8L-103683/4''205297101.5100210x210x320TY-08-12L-1036121''270350101.5100280x280x370TY-08-19L-1036181''305430101.5100315x315x440TY-08-24L-1036241''305485101.5100315x315x495TY-08-36L-1036361''376440101.5100400x400x450TY-08-50L-1036501''380585101.5100395X395X600TY-08-60L-1036601''385670101.5100400x400x685TY-08-80L-1036801''430725101.5100440X440X740TY-08-100L-10361001''490700101.5100530X530X700TY-08-150L-10361501''585820101.5100600X600X830TY-08-200L-103620011/4''628920102100640X640X940TY-08-300L-103630011/4''6801082102100700X700X1100Stainless Steel Expansion Tanks ,Pressure Switch and Pipes also avaible /Stainless Steel Or Carbon Steel all available Basic Introduction The pressure vessel is designed to provide a storage facility and pressure reservoir for water at temperatures up to 99oC. Common uses are in water booster sets, heating pressurisation and fill sets. The vessel incorporates a replaceable Butyl diaphragm mounted in a mild steel shell. This method of construction eliminates any contact between the stored water and the steel shell of the vessel, and is therefore suitable for use with potable water. All units up to and including 25 litre sizes are suitable for a working pressure of 8 bar, larger vessels 10 bar, (except 1000LV)For Water-Dezhi Series Interchangeable membrane pressure tanks.Membranes suitable for drinking water and can be installed to any type of pump.WRc approved and built to 97/23/ECTechnical Parameter ModelTank VolumeMaxi Working PressureDiameterHeightConnectorPackage(Paper Box)ExportPacking SizexLiterBarmmmmInchcmNon-fumigation wooden case/Or Pallet TY-04-5L510160300117x17x31TY-04-8L810200340120x20x34TY-04-12L1210270350127x27x35TY-04-19L1910270410127x27x41TY-04-24L2410270460127x27x46 TY-06-36L3610350560135x35x56TY-06-50L5010350830135x35x83TY-06-60L6010450750145x45x75TY-06-80L8010450890145x45x89TY-06-100L10010450940145x45x94TY-06-150L150104501100145x45x110TY-07-180L180105601000156x56x100TY-07-200L20010650970165x65x97TY-07-300L300107201260172x72x126TY-07-500L500107501500175x75x150TY-07-750L750107501800175x75x180TY-07-1000L100010100018001100x100x180TY-07-1500L150010110020001110x110x200TY-07-2000LPlease refer to customized Model Or Contact Mr.Tom Lee (Export Models Only)TY-08-8L810240330125x25x34TY-08-12L1210270340129.5x29.5x35TY-08-19L1910410290129.5x29.5x41TY-08-24L2410460290129.5x29.5x46TY-08-36L3610380490138x38x50TY-08-50L5010380560138x38x57TY-08-60L6010480490148x48x50TY-08-80L8010480630148x48x64TY-08-100L10010480720148x48x73TY-08-150LPlease refer to customized Model Or Contact Mr.Tom Lee (Export Models Only)TY-08-200LTY-08-250LTY-08-300LTY-08-400LTY-08-500LTY-08-600LTY-08-750LTY-08-1000LTY-08-1500LRegarding Installtion The vessel is supplied pre-charged with air, but this pressure may require adjustment to suit the site conditions. This adjustment must be made with the vessel isolated from the system, and before filling with water. Air may be vented from, or pumped into, a patent valve which will be found under a black plastic screw-off cover on the shell (sizes up to and including 500 litre) or on a side mounted flange (750 and larger). It will be noted that vessels of 60 litre capacity or larger are manufactured with connections at either end of the vessel shell. The vessel should be mounted so that the system connection is made at the lowest possible point, to facilitate on-site maintenance. The other connection may be fitted either with a air bleed valve, or alternatively with a blanking plug. All pressure vessels should be installed with an isolating valve and drain cock.Periodic MaintenanceThe only maintenance required on this equipment is a periodic check on the air cushion pressure. It is necessary to isolate the vessel from the system, and to drain all water from the tank before making this measurement with a standard tyre pressure gauge from the valve.Maintaince free models are also available,Please refer to customized Model Or Contact Mr.Tom Lee (Export Models Only)Company Profile Taizhou Tianyang Electrical co.,LTD. Is located in Shangma industrial Zone,Shitang Town,Wenling City,Zhejiang Province,covering an area of 15,000 square meters.Our Company has over 30 years experience in mold design and exploition. "DEZHI"and "AQUALEADER" are our proprietary brand of our company.We have produced pressure tank for more than 20 years.Available volumes range from 0.5 to 1500 liters.and working pressure from 4 bar to 25bar. Our products are applied to pump systems .Our products are exported to numerous overseas clients.We can custom design and manufacture products according to client-supplied requirements. We adhere to the business philosphy"Credibility,Quality and service",our scientific management is based on the domestic market, but facing to the world.Warmly welcome customers both domestic and from abroad.We sincerely hope to cooperate and develop together to create a better future. Taizhou Tianyang Electrical Co.,Ltd. Is always your most loyal partner. 1.Q: What is your MOQ of this item? A: We are a factory, have stock. 1PCS is ok! 2.Q: What is the delivery time? A:35-45 days after receiving orginal L/C or deposit by TT. 3.Q: Is it all right to make customer's own brand name? A: Yes we supply OEM service. Please send us a authorization doc. 4.Q: Where is your Loading Port? A: Ningbo, Zhejiang, China. 5.Q: What are your payment terms? For Bulk Quantity Purchase A: 30% deposit and balance T/T against copy of Bill of Lading or L/C at sight. For Samll amount Trial Order ,Please arrange the full payment 6.Q: What is your company's available production capacity? A: 90000~120000 pieces of Pressure Tank per month
Purchasing Agent
Note: Send your message to supplier or manufacturer.
Welcome to our Professional and comprehensive procurement services...
Message:
OK ! We suggest you detail your product requirements and company information here.
Enter between 20 to 4,000 characters.
Your inquiry content must be between 20 to 4000 characters.