IPDB › China Industry › Tools & Hardware › Cable Tools
High-Altitude Intelligent No-Mount Cable Optic Automatic Insulation Rod Hanging Machine1
Cable Tools, Cable Tying Machine, Cable Binding Machine
Hebei Leicheng Power Technology Co., Ltd.
Preview:
Product Description Product DescriptionAltitude Optical Cable Binding Machine Line Binding Automatic Cable Tying Machine Automatic Cable Tying Machine is a hand-held, climb-free cable fast tying tool with an integrated intelligent control module, which can automatically complete all the steps of cable tying , and can be widely used in high-altitude operations in the field of communication engineering, it is used to replace the traditional manual hanging and binding cable. This machine is suitable for galvanized wire. The machine is mainly composed of five parts: the main device, special wire disc, battery, remote control switch and hand-held pole.Name: automatic cable tie machine, Optical cable binding machineApplication: cable tying machine, insulation protection Feature: AutomaticPower Source: Rechargeable lithium battery Bundling range: 0-60mmBinding : can binding 1600 times for one time fully charger. Voltage: 12VBattery: 7800 mAh/group, Fully charged, one battery can work more than 1600 times, about 3 kilometers or moreBattery installation mode: external and embedded for your choiceAttached rod: Insulated 10KV, the material is insulated glass epoxy tube, 1.2 m / root, Multiple pieces can be connected together, with a length of 10 metersWireless Remote control switch: remote control distance is 25 meters, can be used in partition wallBinding time: 0.80s/time Power charger time: 1.5hoursWire diameter: Galvanized iron wire 0.8mm, 110meter/roll; Coated iron wire (lined wire) 0.8mm, 110meter/rollGalvanized iron wire:110 meters per plate, 300-700 mm at a time, 150-180 times per plateCoated iron wire:110 meters per plate, 300-700 mm at a time, 150-180 times per plate Product ParametersThe machine is a hand-held free-to-height cable quick-attachment tool with internal components such as controllers that automatically complete all steps of cable tying.It can be widely used in the high-altitude operation in the field of communication engineering and is used to replace the traditional manual attachment strapping cable. The machine is mainly made up of five parts, body, special wire reel, battery, remote control switch and hand-held pole. The body special reels batteries remote switches and hand-held poles. 1. Battery: 7800 mAh/group, voltage 12V, fully charged, a battery can work more than 1600 times, about 3 kilometers or more attached. 2. Attached hanging rod: 10KV insulated, made of insulated glass fiber reinforced plastic epoxy pipe, 1.2 meters per piece. 0.7 kg each. Multiple pieces can be connected together, with a length of 10 meters.3. Coated iron wire: 110 meters per plate, 300-700mm wire at a time, 3 kilometers or more can be attached. Wire diameter 0.8mm, strapping range: 0-60mm 4. Wireless Remote control switch: size 62mm*30mm*12mm, remote control distance is 25 meters in an open space, can be used on partition walls6th Generation cable tying machiine Bundling range0-60mmWire diameterGalvanized iron wire 0.8mmKnotting turns 2 turnsSpeed adjustmentTen levels+Intelligent AdjustmentKnotting success rate98%Rated voltage12VExtension rodWithstand voltage 10Kv, 0.96m/pcs, the material is insulated fiberglass epoxyBattery Capacity15600mA/set (7800mA*2pcs), can work about 2000 times, about 4km or moreGalvanized wire110m/coil, about 700-750mm at a time, about 2km or moreCharge time1.5 hoursRemote controlremote control distance is 80 meters, can be used in partition wallMotorChinaChargerNormalMotherboard2.49 (highly resistant to interference)Dustproof isolation boardYesBearing 11 national standard waterproofShell materialNylon 66Machine heightThe standard length is 5.8mNet weight7 kgGross weight11kgPacking box size101.8*34.4*13.2cm7th Generation cable tying machiine Bundling range0-60mmWire diameterGalvanized iron wire 0.8mmKnotting turns 1-3turns adjustableSpeed adjustmentTen levels+Intelligent AdjustmentKnotting success rate99%Rated voltage12VExtension rodWithstand voltage 10Kv, 0.96m/pcs, the material is insulated fiberglass epoxyBattery Capacity15600mA/set (7800mA*2pcs), can work about 2000 times, about 4km or moreGalvanized wire110m/coil, about 700-750mm at a time, about 2km or moreCharge time1.5 hoursRemote controlremote control distance is 90 meters, can be used in partition wallMotorImportChargerFast chargeMotherboard2.49 (highly resistant to interference)Dustproof isolation boardYesBearing 11 national standard waterproofShell materialNylon 66Machine heightThe standard length is 5.8mNet weight7 kgGross weight11kgPacking box size101.8*34.4*13.2cm8th Generation cable tying machiine Bundling range0-60mmWire diameterGalvanized iron wire 0.8mmNo. of turns1-3 turnsAdjustmentTen levels+Intelligent AdjustmentKnot tying success rate99%Rated voltage12VExtension rodWithstand voltage 10Kv, 0.96m/pcs, the material is insulated fiberglass epoxyBattery Capacity15600mA/set (7800mA*2pcs), can work about 2000 times, about 4km or moreGalvanized wire110m/coil, about 700-750mm at a time, about 2km or moreCharge time1.5 hoursRemote controlremote control distance is 100 meters, can be used in partition wallMotorImportChargerFast chargeMotherboard3.15 (highly resistant to interference)Dustproof isolation boardYesBearing 11 national standard waterproofShell materialNylon 66Machine heightThe standard length is 5.8mNet weight7 kgGross weight11kgPacking box size101.8*34.4*13.2cm9th Generation cable tying machiine Bundling range0-60mmWire diameterGalvanized iron wire 0.8mmNo. of turns1-4 turnsAdjustmentTen levels+Intelligent AdjustmentKnot tying success rate99%Rated voltage12VExtension rodWithstand voltage 10Kv, 0.96m/pcs, the material is insulated fiberglass epoxyBattery Capacity15600mA/set (7800mA*2pcs), can work about 2000 times, about 4km or moreGalvanized wire110m/coil, about 700-750mm at a time, about 2km or moreCharge time1.5 hoursRemote controlremote control distance is 100 meters, can be used in partition wallMotorImportChargerFast chargeMotherboard4.33 (highly resistant to interference)Dustproof isolation boardYesBearing 13 national standard waterproofShell materialNylon 66Machine heightThe standard length is 5.8mNet weight7 kgGross weight11kgPacking box size101.8*34.4*13.2cmProduct Features:1. High working efficiency In the same working environment, it's five times as much as traditional manual work and can work for 10 hours. It independent on the external circumstances and objective factors as well as suitable for all kinds of complex cable tying. Efficiency is greatly improved and labor intensity is reduced . 2. High safely It is electrically insulated from the high voltage of 10 KV . Avoid to the traditional climbing ladder, pulley and other aerial work. It can improve the safety coefficient of operating personnel and reduces safety accidents, which can ensure the safety of personnel. 3. Easy operation of the equipment Simple and convenient remote control , it can be operated by one person independently, which reduce the use of labor force. Because of it can easy to be understand, quick to be used, the different cultural levels and different age groups of workers wide use it. 4. Easy to carry In the traditional construction process, it is necessary to carry the large-scale tools of ladders and some vehicle. As well as three persons can complete the work at least . The machine has the advantages of small size, light weight, detachable packaging, carry conveniently, which reduce the working time, at the same time, it can improve working efficiency.5. Automatic OperationPress the remote control switch it can be adjusted the gear (circled tight or loosen) automatically.Usage method1. Charge the battery. The green light means full charge. The charging time is about 90 minutes. After full charge, insert the host and turn on the host switch. At this time, the buzzer will give a beep indicating that the machine has been powered on.2. Rotate and remove the round cover fixing the cable tray in the middle of the fuselage, and then install the screw tray into the designated position.3. Take out a coil of binding wire and straighten it by hand for 10 cm, insert it into the rectangular inlet hole of the machine body, transport it forward to the bottom, install the binding wire, and rotate the round cover to tight (if the iron wire is not straightened, it is easy to cause wire jam, and the iron wire cannot enter the specified track).4. Start the machine, use the remote control to lead out the binding wire for testing, and send the iron wire out according to the specified track to ensure the successful installation of the wire reel. Warning: When the machine is working, do not touch the tie wire walkway to prevent personal injury.5. Take out the insulating rod with proper height to butt with the battery insulating rod6. Lift the fuselage and select the appropriate line for construction7. Put all the cables to be bundled into the binding groove.8. The construction personnel press the remote control switch, and the attached hanger automatically spins, hinges and cuts off.9. Press it again after one operation. Do not operate it for many times continuously to prevent the two iron wires from winding together.10. If the machine beeps continuously after a long time of inactivity, please restart the power supply and the machine will resume working.11. Adjust the sliding block of the wire tying walkway. First loosen two screws with a tool, and then adjust to an appropriate position. Gradually reduce the diameter of the circle formed by the wire in a clockwise direction, otherwise increase it. The best diameter of wire tapping forming ring is 83-85). Product fault and repair Fault phenomenonContributing factorsResolventThe strapping machine cannot be started, and there is no response when pressing the key1: Battery is dead2: Battery damage3: Poor line contact4: Line faultReplace the battery or charge it. If it cannot be started, open the enclosure to check the circuit or repair itWhen the remote control switch is pressed, the machine is idling and there is no wire out1: No wire in the wire reel 2: When the wire reel is installed, the wire head is not straightened1: Replace the wire reel 2: take out the wire reel and straighten the bent wire headPress the remote control switch, the machine does not work1: The battery is low 2: the gear is blocked by foreign matters 3: the circuit board is faulty1: Charge the battery 2: open the gear part and take out the foreign matters 3: repairThe iron wire cannot be cut after wire tappingThe props are worn or the outlet pressing plate mouth is wornReplace the tool or outlet pressing platePress the remote control switch, only wire is drawn, not bundled1: Hall element sensing position offset 2: Hall element is damaged 3: Line fault1: Install the Hall element into the corresponding position 2: Replace the Hall element 3: RepairCharger LED is not on, unable to chargeCharger faultReplace chargerWire deviation: when binding, the wire arc cannot be fastened outside the jawDuring binding, there is an object blocking the jaw, which interferes with the wire feeding track, causing the wire feeding deviationAdjust the binding angle and remove the foreign matters on the wire outlet track of the jawBuzzer alarm1: Leave the power switch on for more than one minute 2: The battery is dead1: Turn off the power switch and turn it back on 2: Replace the batterySpecial precautions:1. When the wire reel is used about to the last one meter or so, the remaining iron wires must be pulled out along the plastic wire reel. They cannot be directly used up or cut off, otherwise the machine channel will be blocked by iron wires and cannot work. If the iron wire cannot be withdrawn, first check whether the scissors head is clamped. If it is clamped, turn the torsion shaft for several turns with diagonal pliers and it can be withdrawn smoothly.2. It is normal that there may be loose winding. In addition, the new battery has no power or is not charged enough, and there are also loose winding of iron wire. Replacing the fully charged battery will eliminate the problem. Please feel free to use it.3. Do not bundle cables.4. Do not use in rainy days. Packaging & ShippingPackaging & Delivery:Packaging Details: suitable packing for export. Economic Packing design which will save your transportation cost.1. Inside packing: Anti-moisture nylon bag + Carton box + woven belt. 2. Outside packing: carton box or wooden case and pallet. 3. According customer requirement.Port: Shanghai, Qingdao, TianjinLead Time : 7-15daysYou can rest assured that the packaging of the product, as the last link we strictly control! Company ProfileHebei Leicheng Electric Power Technology Co., Ltd. is a professional engaged in power transformers, high and low voltage switchgear and related products R & D, production, sales and service of science and technology enterprises.Since its establishment, the company has been committed to the road of professional development. With strong technical force, advanced equipment at home and abroad, innovative concept and rich manufacturing experience, has passed ISO9000 certification, the use of CAD, to provide customers with suitable regional characteristics of environmental protection, energy saving, low-carbon, high-quality products to meet the basic requirements of the market and different customers. Products are also exported to Central Asia, Africa, Southeast Asia, the Middle East, South America and other countries and regions.At present, the company mainly produces high voltage/low voltage distribution cabinets, prefabricated substations, distribution transformers, dry type transformer, oil immersed transformer, high voltage/low voltage switches and other products.Various electric power fittings and accessories, such as Clamp(Dead end clamp,Cable clamp, Suspension clamp, Tension clamp, Strian clamp etc...), Socket Clevis, Anchor Shackle, Spacer Dampers, Adjuster plates,Yoke plate etc...Various Steel products, such as H-shaped steel, channel steel, steel pipe, Angle steel, hot dip galvanized iron wire, etc., are also our main products! Welcome to shop! Contact me for more product information!Certificates FAQQ: Are you a Manufacturer, factory or Trading company ?A: Yes, We are engaging in the research and development, production and operation of transformer for over 10 years.Q: What's your warranty terms?A: We offer 12 months warranty time.Q: Production Time?A: In general, it take 4~6weeks and it depend on the different style.Q: What's your payment terms?A: Pay by T/T and L/C is acceptable.Q: How do you conduct quality control in your factory?A: We implement 100% QC inspection to ensure every product is qualified. We have over 10 times QC inspections during the manufacturing process from raw material to the final products.Each of our unit has 3C certificate. If you need any other Certificate, we can help you to apply it.Q: Do you have the products in stock?A: Normally no. All our products produce depending to your order quantity. Q: What should provide to make custom transformer ?A: Technical drawing and technical specification document are the best, or you can tell us some details technical specification date as below "Quotation and Ordering Required Information".Q: Could I have your catalog and price list for trial order in MOQ quantity?A: All of our products are showing on Made-in-China or official website, you are always welcome to ask us to get more information directly.
Purchasing Agent
Note: Send your message to supplier or manufacturer.
Welcome to our Professional and comprehensive procurement services...
Message:
OK ! We suggest you detail your product requirements and company information here.
Enter between 20 to 4,000 characters.
Your inquiry content must be between 20 to 4000 characters.