IPDB › China Industry › Manufacturing & Processing Machinery › Ceramic Machine
Lp Gas Ceramic Roller Kiln for Ceramic Mugs1
Ceramic Machine, Ceramic Roller Kiln, Roller Kiln for Ceramic Mugs
Henan Dming Technology Co., Ltd
Preview:
Product Description Product Description1300C Gas heating type Roller kiln tiles sintering kiln Ceramic tableware kilnThis kiln is mainly used for the sintering of terracotta tiles. It can be produced continuously. The daily production capacity is about 9,000 pieces. The rated temperature is 1050 degrees. The fuel is natural gas.ItemNameParameterRemark1ProductTerracottaProduct Height≤4502Production Cycle300-420 MinutesAdjustable 3Rated Temperature≤1050°CLong Term Working Temperature4AtmosphereOxidizingNeutral Flame5FuelLPG 6Calorific Value11000Kcal/m3 7Temperature Uniformity±5°C 8Total Length38 MetersFeeding Table 1 meter/Discharge Table 1 meter9Inner Width1100mmBacking Plate 500*300*15mm/ 3 Pieces Per Row10Unit Length2000mm 11Kiln Unit Number18 Paragraphs 12Kiln Body Width2100mmWidest Size13Kiln Body Height 2200mmAbout 4000(Including The Fan)14Roller Spacing80mm 15Roller Center Height850mm 16Roller SpecificationsФ65×2300mm 17Quantity of Ceramic Roller475 PiecesTotal Number of Whole Kilns18Number of Burners36 Pieces 19Temperature Control6 Sets 20Temperature Detection13 PointsThe Whole Kiln Temperature Detection Point21Transmission Motor10 SetsInverter Control22Fire Damper5 Sets 23Dehumidification Fan1 Set11KW24Combustion Fan1 Set7.5KW25Rapid Cooling Fan1 Set5.5KW26Exhaust Fan1 Set11KW27Tail Cooling Fan2 Sets0.75KW28Combustion System1 SetFrequency Conversion Adjustment29Smoke Exhaust System1 SetFrequency Conversion Adjustment30Quench Pressure System1 SetFrequency Conversion Adjustment31Wind Pressure System1 SetLow Pressure32Gas Pressure Alarm2 SetsHigh Pressure Alarm, Low Pressure Alarm33Drive Motor Alarm1 SetMotor Failure34Fan Alarm System4 SetsSmoke Exhaust/Combustion Support/Rapid Cooling/Heat Extraction35Gas Pressure System1 Setmain pipeline stabilizer1.Introduction to Control System1.1 Temperature Controla. Each temperature control unit is equipped with a thermocouple, a temperature controller and an electric regulating valve. The temperature control system automatically adjusts the proportion according to the temperature of the kiln.b. There are 36 burners in the whole kiln.c. The temperature control unit in the high temperature area is controlled by 6 sections up and down, each section has 6 muskets, 3 on the left and right, staggered and evenly distributed, and the flame is even.d. The burner is a special high-speed burner for oxidizing flame.1.2 Pressure Controla. There are filters, pressure regulator valves, safety solenoid valves, high and low pressure switch alarms and pressure gauges in the gas main process, and operators can make adjustments at any time as needed.b. The combustion-supporting fan has a pressure sensor, which is adjusted by the frequency converter to automatically adjust the set air pressure.c. A kiln pressure sensor is installed at the junction area of the smoke exhaust section and the medium temperature section, and the exhaust fan automatically adjusts the drawing force according to the size of the kiln pressure.d. There are 5 fire baffles in the kiln, which divide the kiln into several districts, and the pressure in the kiln is adjusted and controlled.1.3 Atmosphere Controla. The burner is a special burner specially designed for the proportion of oxidizing flame according to natural gas. The burner burns completely and has good energy saving effect.b. The gas volume of the burner is controlled by the actuator.c. The pressure assembly adjustment system ensures stable wind pressure.d. Baffles and fire-blocking walls are provided in different areas of the kiln to form a combustion chamber to ensure that the oxidizing atmosphere meets the product firing requirements.2. Gas Safety Measures 2.1 Fan Interlock There is an electrical interlocking system between the kiln head exhaust fan → combustion fan → gas assembly solenoid valve. That is, the exhaust fan → the combustion fan → the gas solenoid valve must be turned on in sequence. If they are not turned on in sequence, the gas solenoid valve cannot be started. After the exhaust fan is turned on, a negative pressure state is formed in the furnace, and the residual gas and other waste gas in the furnace will be emptied in time. After the combustion-supporting fan is turned on, each burner will have combustion-supporting air. After the two fans are all turned on, the gas solenoid valve can be turned on to ensure the safety of the kiln ignition. When the two fans are in normal operation, no matter which fan suddenly stops, the gas main solenoid valve will immediately close the valve to cut off the gas to ensure the safety of the kiln.2.2 Pressure SensorA kiln sensor is installed on the combustion-supporting fan pipeline. After the combustion-supporting fan is started, the gas solenoid valve can be activated only after the pressure sensor detects that there is pressure. Conversely, if the pressure sensor cannot detect the wind pressure, the gas solenoid valve cannot be activated.2.3 Main Solenoid Valve and Emptying Solenoid ValveAt the end of the main gas pipe of the kiln, an automatic emptying device is installed. When the main gas solenoid valve is opened, the emptying solenoid valve will be closed immediately and no longer emptying. When the main gas solenoid valve is closed, the emptying solenoid valve immediately opens the switch to empty the room. After emptying, the main gas pipeline of the kiln will lose pressure, and no more gas will be sprayed into the furnace through the burner to ensure the safety of the kiln. Our Advantages Company Profile
Purchasing Agent
Note: Send your message to supplier or manufacturer.
Welcome to our Professional and comprehensive procurement services...
Message:
OK ! We suggest you detail your product requirements and company information here.
Enter between 20 to 4,000 characters.
Your inquiry content must be between 20 to 4000 characters.