CIPDB › China Industry › Chemicals › Paint & Coating
763 Water-Based Inorganic Floor Finish for Industrial Workshops and High-Traffic Areas1
Paint CoatingMarking PaintCoating Paint
Jiangsu Shuocheng New Materials Technology Co., Ltd.
Preview:
Product Description Notes1. This product is for professional use only, construction workers need training, experience, ability and equipment to use it correctly (mixing/stirring and applying this coating product) according to ourd technical documents.2. Construction workers need to use correct and appropriate personal protective equipment when using this product, this guidance is based on existing product knowledge.3. Any changes recommended to adapt to site conditions must be approved by our technical and service representatives before use.Coating process requirements1. When carrying out coating work, it is advisable to carry out the work under the environmental conditions of temperature 10-35°C and relative humidity below 75%. The moisture content of the base surface is required to be below 20%. Construction should be avoided on rainy days or when the relative humidity of the atmosphere is higher than 80%, or when the temperature is below 10°C.2. Air spraying, high-pressure airless spraying, rolling/brushing/scraping and other methods can be used for coating work; in order to obtain betterl coating quality, it is recommended to use roller/brush coating. Note that there should be no water in the roller brush and spray gun; reference paint amount: 0.15-0.25kg/m2.3. According to different coating forms, the original paint can be used after stirring evenly. If necessary, add appropriate amount of water to dilute it for coating and adjust the viscosity of the paint liquid, but the amount added shall not exceed 10% of the coating amount.4. After the paint film coating is completed, it should be protected within 72 hours to avoid contact with any water (liquid substances) to avoid affecting the quality of the coating;5. This product is a single-component product, which can be used immediately after opening the can. If it is not used up, it should be sealed and stored in time. If it is not stored properly, the viscosity of the paint will increase, gelling until it is completely solidified. In this case, even if it is forcibly painted, physical properties such as adhesion and protection will be affected.Storage and transportation1. It must be stored in accordance with national regulations; the storage environment should be dry, cool, well ventilated, avoid direct sunlight, andl stay away from heat and fire sources. The packaging container must be kept sealed; handle it carefully, from the date of production, the effective storage period is 6 months (stored in a sealed container). After the storage period, it must be inspected and qualified before use.2. During transportation, the product should avoid extrusion, severe cold, rain, and sunlight exposure, and should comply with the relevant regulations of the transportation department. Health and Safety1. Please read the safety notices and product instructions on the container packaging in detail. Use under well-ventilated conditions. During painting operations, the respiratory organs must be protected from spray damage, and paint mist should be avoided. Skin and eye contact with this type of product should be avoided. It is best to wear a ventilated mask, safety goggles and protective gloves; if accidentally splashed on the skin, rinse immediately with appropriate detergent, soap and water. If accidentally enters the eyes, rinse thoroughly with water and seek medical treatment immediately.2. The construction site must be well ventilated. When working in narrow places or places where air is not circulated, strong ventilation must be provided.3. The construction site must be equipped with certain fire prevention and firefighting equipment.4. This product should not flow into the sewage system.5. For detailed safety measures, see the Material Safety Data Sheet (MSDS) of this product; in addition, the safety regulations stipulated by the relevant country or local government should be observed.Color differenceThis product is mainly used as a topcoat, and the color may vary slightly from batch to batch.Disclaimer1. The information provided in this manual is entirely based on our understanding in the laboratory and practice. Shuocheng's products are considered semi-finished products; the use of such products is usually beyond our control; so Shuocheng only guarantees the quality of the product itself; in order to adapt to local regulations, the product may be appropriately adjusted, and we reserve the right to modify the manual without further notice;2. For your own needs and specific applications, please consult our service department: 0516-83316660 to obtain specific guidance on the applicable performance of the relevant products.Product ParametersSingle component: 363 water-based acrylic floor paintProduct DescriptionThis product adopts the technology imported from Germany, and is made of inorganic mineral silicon and nano-silicon dioxide, which is an environmentally friendly and ecological super-weather-resistant nano-inorganic silicone resin. The coating prepared with this as the film-forming material solves the problems of unstable storage, difficult color adjustment, easy stratification, easy cracking, poor weather resistance, stain resistance, color retention, and color development of traditional inorganic coating systems.Product FeaturesGood weather resistance, strong adhesion, high strength; rich colors, can be adjusted at will; hardness up to 2H; suitable for cement-based surfaces; high temperature resistance above 80 degrees, no re-adhesion; super strong UV resistance and long-lasting non-fading performanceApplication FieldsSuitable for ground construction with environmental protection requirements such as medicine, schools, homes, outdoor parks, offices, etc.Packaging specificationsSingle component: Single component acrylic floor paint 25kg/barrelProduct ParametersItemTest/StandardDescriptionColor/Color CodeGB11186As agreedEffective Usage Time/Ready for use upon openingDrying Time: Surface Dry/Through Dry10°C1H/2H25°C0.5H/1H35°C0.5H/1HDensity (g/ml)GB/T 67501.3±0.1Solid Content (%)GB/T 1725≥40%Theoretical Coverage60-80um (based on dry film thickness)6-4m2/kgNote: The data listed is based on factory batch production and may vary slightly due to color and batch differences.Construction condition parametersDiluent: Deionized water/clean tap waterDilution ratio: <10%Surface treatment1. To ensure that the coating has good and lasting adhesion, all substrate surfaces must be clean, dry and free of pollutants.2. After ensuring that the surface of the single-component sealing primer has dried, the single-component topcoat or midcoat can be directly applied;Note: The recommended surface treatment can obtain the best performance including adhesion, physical resistance and chemical resistance. Construction technologyConstruction technology Construction methodBrushing Use the cross-cross method for brushingRoller coating Use the cross-cross method for roller coatingSpraying Use airless spray or air spray to spray using the cross-cross method.Anti-static: water-based epoxy anti-static finishProduct Description This product is an antistatic two-component epoxy topcoat product. It uses imported resins, high-quality solvents with low VOC content, conductive media and pigments, solvents, BYK additives, and American Gas Company curing agents. It is refined through professional technology and production processes. It is a high-solid content, low-viscosity two-component material. Antistatic flat coating has a series of excellent characteristics: such as rapid leakage of static charge, high mechanical wear resistance and adhesion, excellent chemical resistance, acid, alkali, salt solution and petroleum products, fast curing speed of paint film coating, good appearance decoration effect, etc.Product characteristicsThis product is solvent-free and environmentally friendly, the paint film coating has no seams, does not dust, is easy to clean, and has a smooth and bright surface, it can quickly leak static charge to prevent electronic parts from being damaged and fires caused by static electricity accumulation.Application field This product is suitable for places where antistatic is required in industries such as power plants, communications, microelectronics factories, precision machinery factories, and chemical factories. It is especially suitable for production workshops and storage areas of sensitive electronic instruments, integrated circuits and other electronic components with high antistatic requirements.Packaging specifications Two components: Component A: Antistatic epoxy floor paint 15kg/barrel Component B: Curing agent 2.5kg/barrelProduct ParametersItemTest/StandardDescriptionColor/Color Code (Component A)GB11186As agreed colorColor/Color Code (Component B)GB11186Light yellowEffective Usage Time (Pot Life)10°C 25°C 30°C120min 35min 28minDrying Time: Surface Dry/Through Dry10°C 25°C 30°C10h/40h 8h/30h 5h/24hSurface Resistance, Volume Resistance (Anti-static Type) 1×10^4^Ω - 1×10^6^ΩSurface Resistance, Volume Resistance (Electrostatic Dissipative Type) 1×10^4^Ω - 1×10^6^ΩSolid Content (%)GB/T 1725 (After mixing A/B)≥90Density (g/ml) (Component A/B)GB/T 67501.2±0.05/0.85±0.05Theoretical Coverage40-60um (based on dry film thickness)1.4-0.7m2/kgVOC (g/L)After mixing A/B<30%Construction condition parametersPaint mixing ratio (mass ratio): A: B = 4: 1Thinner: Special thinnerDilution ratio: ≤10%Construction processConstruction process Construction method:Brushing: Use cross-cross method for brushingRolling: Use cross-cross method for roller coatingScraping: Use 50% overlap cross method for scrapingSpraying: Use airless spray or air spray using cross-cross method for spraying.Anti-static: water-based epoxy anti-static free-flow surface paintProduct DescriptionThis product is a solvent-free two-component epoxy self-leveling surface paint product. It is a two-component, self-leveling, seamless, high-performance thick-coating epoxy floor coating produced with high-quality imported raw materials. The product has a high coating thickness, a smooth and beautiful surface, and is durable. It is suitable for use in places with high requirements for floor coating and has good matching with our epoxy intermediate paint products.Product FeaturesThe paint film has a smooth surface, beautiful color, and a mirror effect. It is solvent-free, odorless, pollution-free, non-toxic, environmentally friendly, and has acid, alkali, and chemical resistance. It has good resistance to moisture, salt spray, oils, and organic solvents.Application FieldsThis product is suitable for the electronics, aerospace, and microelectronics industries that require high cleanliness, beauty, dust-free, and sterility, and areas with high requirements for mechanical and chemical comprehensive performance.Packaging specificationsTwo components:Component A: Solvent-free epoxy floor paint 16kg/barrelComponent B: Curing agent 4kg/barrelProduct ParametersItemTest/StandardDescriptionColor/Color Code (Component A)GB11186As agreed colorColor/Color Code (Component B)GB11186Light yellowEffective Usage Time (Pot Life)15°C60min25°C30min30°C15minDrying Time: Surface Dry/Through Dry(Surface dry for walkable condition)15°C48h/240h25°C2h/168h30°C12h/96hPencil Hardness (Grade)GB/T 6739≥2HAdhesion (Cross-cut Test) (Grade)GB/T 9286≤1Impact Resistance (kg·cm)GB/T 1732≥50Water Resistance (7d)No bubbles, no peeling, slight color change allowedNo change after 60hSalt Water Resistance (3% NaCl/7d)No bubbles, no peeling, slight color change allowedNo change after 60hAlkali Resistance (10% NaOH/48h)No bubbles, no peeling, slight color change allowedNo change after 60hAcid Resistance (10% H2SO4/48h)No bubbles, no peeling, slight color change allowedNo change after 60hOil Resistance (20# Lubricating Oil/48h)No bubbles, no peeling, slight color change allowedNo change after 60hSolid Content (%)GB/T 1725 (After mixing A/B)≥90Density (g/ml) (Component A/B)GB/T 67500.96±0.1/1.6±0.1Theoretical Coverage40-60um (based on dry film thickness)6-4m2/kgVOC (g/L)After mixing A/B<2%Construction condition parametersPaint mixing ratio (mass ratio): A: B = 4: 1Thinner: Special thinnerDilution ratio: ≤3%Construction processConstruction process Construction method:Brushing Use cross-cross method for brushingRolling Use cross-cross method for roller coatingScraping Use 50% overlap cross method for scrapingSpraying Use airless spray or air spray with cross-cross method for spraying.Epoxy thin coating: 2601 waterborne epoxy floor sealing primerProduct DescriptionThis product is a water-based two-component product. The epoxy water-based universal primer/midcoat is made by our company by selecting imported water-based epoxy resin, water-based surface additives, and imported water-based curing agent and other raw materials. It is prepared through advanced production technology. It is an environmentally friendly water-based epoxy primer material.Product FeaturesIt does not contain organic solvents, is safe and pollution-free, meets environmental protection requirements, saves energy, uses water as a dispersion medium, has little odor, is non-flammable and non-explosive, and its safety during storage, transportation and use is guaranteed.Application AreasAs a universal base/midcoat stock solution for epoxy resin series floor coatings, it is used for base/midcoat universal coatings on wet concrete floors.Packing SpecificationsTwo-component:Component A: Water-based epoxy floor sealing primer 18kg/barrelComponent B: Curing agent 6kg/barrelProduct ParametersItemTest/StandardDescriptionColor/Color Code (Component A)GB11186Light yellowColor/Color Code (Component B)GB11186TransparentEffective Usage Time (Pot Life)15°C120min25°C60min35°C40minDrying Time: Surface Dry/Through Dry15°C8h/24h25°C4h/14h35°C2h/8hAdhesion (Cross-cut Test) (Grade)GB/T 9286≤1Density (g/ml)GB/T 67501.05Solid Content (%)GB/T 1725 (After mixing A/B)≥65Theoretical Coverage40-60um (based on dry film thickness)6-3m2/kgNote: The data listed is based on factory batch production products, and there will be slight changes due to different colors and batches.Construction condition parametersPaint mixing ratio (mass ratio): A: B = 3: 1Dilute with water to 60% of the total amountConstruction processConstruction process Construction method:Brushing Use cross-cross method for brushingRolling Use cross-cross method for roller coatingSpraying Use airless spray or air spray to spray using cross-cross method.Epoxy thin coating: 2602 water-based epoxy floor medium coatingProduct DescriptionThis product is made of imported water-based epoxy resin, excellent water-based surface additives, imported high-emulsification water-based curing agent, and high-strength self-flowing cement mortar and other raw materials. It is prepared through advanced production technology. It is a zero-VOC, high bonding strength, and reduced unit film thickness material cost.Product FeaturesIt does not contain organic solvents, is safe and pollution-free, meets environmental protection requirements, saves energy, uses water as a dispersion medium, has little odor, is non-flammable and non-explosive, and is safe during storage, transportation and use.Application FieldsAs a universal stock solution for the base/middle of epoxy resin series floor coatings, it is used for the base/middle general coating of wet concrete floors; it can also be used as a universal middle coating for epoxy resin series floor coatings, and is used for the middle coating of wet concrete floors.Packaging SpecificationsTwo-component:Component A: Water-based epoxy floor middle coating 20kg/barrelComponent B: Curing agent 4kg/barrelProduct ParametersItemTest/StandardDescriptionColor/Color Code (Component A)GB11186As agreedColor/Color Code (Component B)GB11186Off-whiteEffective Usage Time (Pot Life)10°C60min25°C30min35°C20minDrying and Re-coating Time:Surface Dry/Through Dry/Re-coating10°C5h/12h/12h25°C3h/8h/8h35°C2h/6h/6hDensity (g/ml) (Component A/B)GB/T 67501.05/1.05Solid Content (%)GB/T 1725 (After mixing A/B)≥76Theoretical Coverage180-200um (based on dry film thickness)0.28-0.25m2 /kgNote: The data listed is based on factory batch production products, and there will be slight changes due to different colors and batches.Construction condition parametersPaint mixing ratio (mass ratio): A: B = 5: 1Dilute with water to 10% of the total amountEmulsion: aggregate = 1: 0.8-1.5Construction processConstruction process Construction method:Scraping Use 50% overlap cross method for scrapingTroweling Use 50% overlap cross method for trowelingEpoxy thin coating: 2603 water-based epoxy floor finishProduct DescriptionThis product is made of imported water-based epoxy resin, excellent surface additives, imported water-based curing agent and other raw materials selected by our company, and is formulated through advanced production technology. It is a high-performance topcoat material with low VOC, environmental protection, high bonding strength and low viscosity.Product Features1. Safe and environmentally friendly, pollution-free and odorless, does not contain organic solvents, and meets environmental protection requirements; the paint has low viscosity, good flow and leveling, and high strength. It is non-flammable and non-explosive, and the safety during storage, transportation and use is guaranteed. (1. High strength and long operating time; 2. Small gloss difference and no color difference; 3. Excellent chemical resistance and yellowing resistance)Application FieldSuitable for ground construction with environmental protection requirements such as food, medicine, school, and home.Packing SpecificationsTwo-component:Component A: Water-based epoxy floor intermediate paint 20kg/barrelComponent B: Curing agent 5kg/barrelProduct ParametersItemTest/StandardDescriptionColor/Color Code (Component A)GB11186As agreedColor/Color Code (Component B)GB11186TransparentEffective Usage Time (Pot Life)10°C60min25°C45min35°C30minDrying and Re-coating Time:Surface Dry/Through Dry10°C8h/16h25°C5h/14h35°C2h/12hDensity (g/ml) (Component A/B)GB/T 67501.2/1.1Solid Content (%)GB/T 1725 (After mixing A/B)≥80Theoretical Coverage40-60um (based on dry film thickness)5-3m2 /kgNote: The data listed is based on factory batch production products, and there will be slight changes due to different colors and batches.Construction condition parametersPaint mixing ratio (mass ratio): A: B = 5: 1Water dilution amount: 5-10%Construction processConstruction process Construction method:Spraying Use 50% overlap (cross) cross method for scrapingRoller coating Use 50% overlap cross method for rollingScraping Use 50% overlap cross method for scrapingOther epoxies: water-based epoxy orange finishProduct DescriptionThis product is an orange peel type two-component epoxy topcoat product. It uses imported resin, high-quality solvents, special aggregates, BYK additives, American Gas Company curing agents and other raw materials. It is developed through professional technical modification. It has high solid content and excellent physical properties: anti-slip and super wear resistance, and the surface color is gorgeous.Product FeaturesThis product is made of solvent-free epoxy resin and high-quality curing agent; the surface has an orange peel effect, and the pattern can be large or small; good corrosion resistance to acids, alkalis, salts and greases; excellent wear resistance, pressure resistance and impact resistance;Application FieldsThis product is suitable for places where anti-static is required in industries such as power plants, communications, microelectronics factories, precision machinery factories, and chemical factories. It is especially suitable for sensitive electronic instruments with high anti-static requirements, production workshops and storage areas of electronic components such as integrated circuits.Packing SpecificationsTwo-component:Component A: Anti-static epoxy floor topcoat 15kg/barrelComponent B: Curing agent 2.5kg/barrelProduct ParametersItemTest/StandardDescriptionColor/Color Code (Component A)GB11186As agreed colorColor/Color Code (Component B)GB11186TransparentEffective Usage Time (Pot Life)15°C240min25°C120min30°C60minDrying Time: Surface Dry/Through Dry(Surface dry for walkable condition)15°C8h/24h25°C4h/168h35°C2h/96hSolid Content (%)GB/T 1725 (After mixing A/B)≥90Density (g/ml) (Component A/B)GB/T 67501.15±0.05/0.95±0.05Theoretical Coverage40-60um (based on dry film thickness)3.5-2.5m2 /kgConstruction condition parametersPaint mixing ratio (mass ratio): A: B = 5: 1Thinner: Special thinnerDilution ratio: ≤10%Construction processConstruction process Construction method:Brushing Use cross-cross method for brushingRolling Use cross-cross method for roller coatingScraping Use 50% overlap cross method for scrapingSpraying Use airless spray or air spray using cross-cross method for spraying.Inorganic: 761 water-based inorganic floor sealing primerProduct IntroductionSingle-component inorganic floor primer is made of inorganic organic hybrid resin as raw material and water as diluent. The product dries quickly and has excellent permeability and adhesion.Product ApplicationUsed as a closed primer on the surface of concrete, cement and other substrates.Product FeaturesStrong permeability, excellent sealing performance, can improve the strength of the substrate.Excellent adhesion to the substrate.High modulus potassium silicate products do not contain volatile solvents and have excellent environmental performance.High temperature resistance and excellent alkali resistance.Performance indicatorsItemTest/StandardDescriptionColorGB11186TransparentFineness (um)GB/T 6753≤30Solid Content (%)GB/T 1725>20Density (g/ml)GB/T 67501.1±0.1Adhesion (Cross-cut Test) (Grade)GB/T 9286≤1Water Resistance Salt Water Resistance (3% NaCl) Acid Resistance (10% H2SO4) Alkali Resistance (10% NaOH) Oil Resistance (45# Engine Oil) Self-leveling epoxy: 2614 water-based epoxy self-leveling floor finishProduct DescriptionThis product is a general-purpose two-component epoxy self-leveling paint product. It is a two-component, self-leveling, seamless, high-performance epoxy floor self-leveling paint produced with high-quality imported raw materials. The surface of the product is smooth and beautiful, colorful, pressure-resistant, wear-resistant, and durable. It is suitable for places with high requirements for floor coating and has good matching with our epoxy intermediate paint products.Product FeaturesThe surface of the paint film coating is flat and bright with a mirror effect; seamless and dust-free, the surface is smooth and easy to clean, with high wear resistance, and the dense paint film surface can resist the erosion of various chemicals. A variety of color appearances are available for customers to choose.Application FieldsThis product is suitable for places with high requirements for cleanliness and beauty, such as shopping malls, exhibition halls, corridors, food factories, pharmaceutical factories, clean workshops, underground parking lots and other floors.Packing SpecificationsTwo-component:Component A: Solvent-free epoxy floor topcoat 20kg/barrelComponent B: Curing agent 4kg/barrelProduct ParametersItemTest/StandardDescriptionColor/Color Code (Component A)GB11186As agreed colorColor/Color Code (Component B)GB11186Light yellowEffective Usage Time (Pot Life)10°C120min25°C60min30°C45minDrying Time: Surface Dry/Through Dry(Surface dry for walkable condition)10°C12h/48h25°C8h/36h30°C3h/24hPencil Hardness (Grade)GB/T 6739≥2HAdhesion (Cross-cut Test) (Grade)GB/T 9286≤1Impact Resistance (kg·cm)GB/T 1732≥50Water Resistance (7d)No bubbles, no peeling, slight color change allowedNo change after 60hSalt Water Resistance (3% NaCl/7d)No bubbles, no peeling, slight color change allowedNo change after 60hAlkali Resistance (10% NaOH/48h)No bubbles, no peeling, slight color change allowedNo change after 60hAcid Resistance (10% H2SO4/48h)No bubbles, no peeling, slight color change allowedNo change after 60hOil Resistance (20# Lubricating Oil/48h)No bubbles, no peeling, slight color change allowedNo change after 60hSolid Content (%)GB/T 1725 (After mixing A/B)≥90Density (g/ml) (Component A/B)GB/T 67501.3±0.1/0.96±0.1Theoretical Coverage40-60um (based on dry film thickness)1.4-0.7m2 /kgVOC (g/L)After mixing A/B<30%Construction condition parametersPaint mixing ratio (mass ratio): A: B = 5: 1Thinner: Special thinnerDilution ratio: ≤10%Note: All data are valid only for mixed paint.Construction processConstruction process Construction method:Brushing: Brushing with cross-cross methodRolling: Roller coating with cross-cross methodScraping: Scraping with 50% overlap cross methodProduct DescriptionOur AdvantagesCompany ProfileFounded in 2016, Jiangsu Shuocheng New Material Technology Co., Ltd. is an environmentally friendly technology enterprise that specializes in the research and development, production, and sales of water-based paint products. The company is precisely positioned in the mid-to-high-end water-based paint market, committed to becoming a leading brand in this field, with the sacred mission of providing high-quality, high-performance, and environmentally friendly water-based paint products.Located in the Xuzhou National High-tech Industrial Development Zone, a state-level high-tech industrial development zone approved by the State Council, the company not only has an independent research and development institution but also owns proprietary intellectual property rights. It has established long-term and stable cooperative relationships with several well-known scientific research institutions. In addition, the company has successfully obtained ISO9001 Quality Management System, ISO14001 Environmental Management System, and ISO18001 Occupational Health and Safety Management System certifications, fully demonstrating the company's high standards and strict requirements in quality management, environmental protection, and employee occupational health.The company's main products cover various systems of water-based paints, including water-based acrylic systems, water-based alkyd systems, water-based epoxy systems, water-based acrylic polyurethane systems, water-based amino baking paints, etc. These products are widely used in many industries such as architectural decoration, machinery manufacturing, hardware and electrical appliances, automobiles, and ships.With advanced production equipment, strong technical strength, and comprehensive after-sales service, the company has firmly established itself in the water-based paint field with its exceptional product quality and precise market orientation. Several products of the brand "Shuocheng Waterborne Paint" have been awarded national invention patents, standing out in the fiercely competitive industry.At this stage, the company is actively expanding market share and enhancing brand awareness. It plans to achieve a significant increase in the market share of domestic mid-to-high-end water-based paints in the coming years and gradually explore international markets.The company always adheres to the concept of "lucid waters and lush mountains are invaluable assets," strictly controlling quality from the source of the product supply chain. It unswervingly strives to provide high-quality water-based coating products and considerate services for customers and society, aiming to set a model for the green development of the industry and contribute to the construction of a beautiful China.CertificationsFAQQ1, Are you manufacturer or trading factory?A: In fact we are the factory 10 years, can supply all types of paint. Q2, If the OEM is accepted?A: Yes, OEM is welcome. We also can do your own logo and package. Q3, If I do not know which paint to choose, what shall I do?A: Please no need to worried about this, we have the professional engineer, colorist, and experienced sales, can give you the suggestion for paint and coating. Q4, What's are your payment term?A: We can accept the TT, Western Uniono, LC, Credit card, and Alipay, and others please contact with us freely. Q5, Can you accept to supply the free sample?A: Yes, of course we are glad to supply the free sample, and you need in charge of the freight cost. Q6, What's your products' advantages?A. Good quality and competitive prices.B. Strictly quality control when producing.C. Professional team work, from design, development, producing,assemble,packing and shipping.D. Experience for shipping the paint to different countries. Q7, Can we visit your factory?You are Warmly welcomed to visit our factory, it would be our great pleasure!
Purchasing Agent
Note: Send your message to supplier or manufacturer.
Welcome to our Professional and comprehensive procurement services...