CIPDB › China Industry › Metallurgy, Mineral & Energy › Metal Stocks
Lork Spot Goods Uns S13800/AMS 5864/ASTM A693 Steel Rod for Aerospace Components pH13-8mo Stainless Steel Bar1
Metal StockspH13-8moASTM A693
LORK GROUP CO., LTD
Preview:
Product Description Product Description IntroductionLork Group specializes in the supply of PH 13-8 Mo Bar raw materials and processing, alloys, stainless steel, metal quality development, welcome your inquiries.PH 13-8 Mo is a stainless steel with approximately 13% chromium and 8% nickel content that has good resistance to corrosion in general as well as to stress corrosion cracking. PH 13-8 Mo offers better mechanical properties in demanding environmental conditions in comparison to other materials based on iron. Precise control of the microstructure is achieved through vacuum melting and remelting. Medium to high strength can be achieved through precipitation hardening aging treatments.Precipitation-Hardening Stainless Steel PH 13-8 Mo | 1.4534 ApplicationsAerospace componentsInjection molding equipmentWaterjet cutting equipmentPetrochemical industriesNuclear industriesStainless Steel PH13-8MO Common Trade NamesPH13-8MoXM-13UNS S13800DMS 2100 GradeHMS 6-1105 REV A AMD 3ST0160LB0013 REV EASTM F899-12BRMS-150 REV N for sizes 3.625" MaxSAE 13-8ATI 13-8 Supertough AlloyStainless Steel PH13-8MO Chemical Composition Chemical composition - limits in %FeRestCr12,25 - 13,25Ni7,50 - 8,50Mo2,00 - 2,50Al0,90 - 1,35Mnmax. 0,20Nmax. 0,10Simax. 0,10Cmax. 0,05Pmax. 0,01PH13-8MO Physical constants and thermal propertiesDensity7,76 g/cm3Melting point1404 °CThermal conductivity at 20°C12,8 W/m · °CElongation coefficient at20-100°C13 μm/m · °CPH13-8MO Typical mechanical properties (room temperature)H950 Yield strengthmin. 1413 MPaTensile strengthmin. 1517 MPaElongationmin. 10 %H1000 Yield strengthmin. 1310 MPaTensile strengthmin. 1413 MPaElongationmin. 10 %H1050 Yield strengthmin. 1138 MPaTensile strengthmin. 1207 MPaElongationmin. 12 % WorkabilityHot WorkingPH 13-8 Mo stainless can be readily forged, hot headed and upset. Material which is hot-worked must be solution treated prior to hardening if the material is to respond properly to hardening.ForgingHeat uniformly to 2150/2200°F and hold 1 hr at temperature before forging. Do not forge below 1750°F. To obtain optimum grain size and mechanical properties, forging should be cooled in air to 60°F before further processing. Forging must be solution treated prior to hardening.Cold WorkingPH 13-8 Mo stainless can be fabricated by cold working to an extent which is limited by the high initial yield strength.CuttingBars and forging billets should be cold cut by sawing. Abrasive wheel cutting can cause small surface cracks, particularly when cutting annealed stock, and should be avoided.MachiningPH 13-8 Mo stainless can be machined in both the solution treated and various age-hardened conditions. In Condition A the alloy gives good tool life and surface finish when machined at speeds 20 to 30% lower then those used for Custom 630 (17Cr-4Ni) or 20 to 30% lower than used for Stainless Type 302 and 304. The machinability as age-hardened will improve as the hardening temperature is increased.Conditon H 1150M provides optimum machinability. Having procures Conditon H 1150M for best machinability, higher mechanical properties can be developed only by solution treating and heat treating at standard hardening temperatures.WeldingPH 13-8 Mo stainless can be welded using the inert-gas shielded or resistance welding processes. When a filler metal is required, PH 13-8 welding consumables should provide welds with properties similar to those of the base metal. When designing the weld joint, care should be exercised to avoid stress concentrators, such as shrap corners, threads, and partial-penetration welds. When high weld strength is not needed, a standard austenitic stainless filler, such as E/ER308L, should be considered.Normally, welding in the solution annealed condition has been satisfactory; however, where high welding stresses are anticipated, it may be advantageous to weld in the overaged (H 1150) condition. Usually, preheating is not required to prevent cracking. If welded in the solution treated condition. the alloy can be directly aged to the desired strength level after welding. However, the optimum combination of strength, ductility and corrosion resistance is obtained by solution treating the welded part before aging. If welded in the overage condition, the part must be solution treated before aging.Available Sizes And SpecificationsPH13-8Mo stainless steel plate sizes and specificationsGradePH13-8MoCold rolled stainless steel plateThickness: 0.3mm- 16.0mm, Width: 1000mm - 2000mm,Length: as requirements, Surface: 2B/BA/SB/8K/HL/1D/2D etcHot rolled stainless steel sheetThickness: 3.0mm - 300mm, Width: 1000mm - 3000mmLength: as requirements, Surface: No.1/picklingStandardASTM A240/A480, ASTM B688, ASTM B463/SB463, ASTM B168/SB168, ASTM B443/SB443/B424/SB424B625/SB625 B575/SB575, JIS G4303,BS 1449, DN17441, G4305Stainless steel plateThickness: 8.0mm - 300mm, Width: 1000mm - 3000mmLength: as requirements, Surface: No.1/pickling Surface Treatment DetectionProcessing Packaging & ShippingCompany ProfileFAQQ1: Do you accept the trial order ?A1: Yes,if we have the exactly size in stock.we can delivery even 1 piece/meter .Q2: Can I have free sample before making orders?A2: Yes,we can supply free sample as requirement,but buyer needs to pay the freight charges ,the freight fee will return to buyer after making order.Q3: How do you control the quality ?A3: MTC and PMI will be sent before shipment,any 3rd party inspection if need .Q4: How about your delivery time ?A4: Generally delivery time is 15 working days .Q5: How can I quickly get the price list ?A5: Directly click "chat now" or send us email with detail specifications,you will get the official price list in 1 hour .
Purchasing Agent
Note: Send your message to supplier or manufacturer.
Welcome to our Professional and comprehensive procurement services...