1050 H14 Stucco Aluminum with Polykraft¹

Product Description 1050 H14 Stucco Aluminum with PolykraftProduct Description        All the properties of lubricant used in food packaging aluminum foil must conform to conventional lubricating lubricant, which can reduce the friction and wear of all technical parameters required, and avoid corrosion, good thermal performance, sealing effect. In addition, they also need to meet the food regulations and biological inertia, that does not affect the taste, does not affect the odor, does not affect the color, in line with the international standards (TRIOA ORIGINAL).Certification of food grade lubricant products are divided into three types: 3H, H1 and H2. The certification is responsible for the selection of the international body of (independent certification body).3H grade lubricant: suitable for lubricant must be in contact with food occasions, such as: oven mold.H1 grade lubricant: suitable for lubricant that are easy or cannot avoid contact with food.H2 grade lubricant: suitable for occasions where there is no direct contact with food.The production process of aluminum foil lunch box can be divided into six steps: material spreading, lubricating, feeding, punching forming and blanking. Aluminum foil in the production process by the pressure of up to 40~80 tons, punching frequency of 1~2 seconds, the average production capacity of 20 thousand / day, aluminum foil storage shelf life of 2 years. In this process, lubricant plays a very important role, including: heat, cooling, protection of aluminum foil surface protection, stamping equipment and tooling, anti rust, corrosion and prevent the bonding surface of the aluminum foil (adapted to pre coated well lubricated foil need to roll up the situation, such as aluminum foil lubricant market at present most) selection of food grade DOS lubricant, Germany, Henkel and Sasol lubricant.Lubricant content:Different aluminum foil material, lunch box type and size, the amount of lubricating lubricant is also different, the amount of lubricant required for the range of 20mg~300mg/ m2. If the lubricant volume is low, insufficient lubrication, easy deformation, damage output boxes or even scrapped; on the contrary, if the lubricant volume is high, excessive aluminum foil lubricant rolling lubrication, because the roll surface caused by extrusion, aluminum volume drop phenomenon, produce box easy to stick to the mold surface is not easy to blanking. Stop out, causing serious impact on production efficiency. At the same time, excessive lubrication is also a waste, improve production costs. Lubricating way according to the different lubrication requirements, there are two types of lubricant and double side lubricant. Single side lubricant is suitable for the simple type of lunch box, the small deformation of aluminum foil lubricant and the low requirement of lubricant, the lubricant filling mode must be strictly controlled to avoid unnecessary waste.Detailed Photos 1. ConstructionAluminum sheet is widely used in the construction industry, mainly used in building exterior walls, interior decoration, roof covering, door and window frames, ceilings, etc. The advantage of aluminum plate is that it is lightweight, easy to handle and install. At the same time, it also has very good sound insulation, heat insulation, durability and other properties, which can greatly improve the service life of the building. 2. Vehicle manufacturingAluminum sheets also have a wide range of applications in the vehicle manufacturing industry. It can be used to make car frames, body shells, wheel hubs, etc. Compared to the traditional steel body, the aluminum plate body is lighter, which can reduce the overall weight of the vehicle and improve fuel efficiency. At the same time, the aluminum plate also has good strength and heat resistance, which can ensure the stable operation of the vehicle in various harsh environments.3. Medical device manufacturingAluminum sheets also have many uses in the manufacture of medical devices, such as surgical instruments, infusion bottles, etc. Instruments made of aluminum plates have good anti-corrosion properties and are easy to clean, which can ensure hygiene and safety in the medical process.4. Electronics industryAluminum sheet also has a very important application in the electronics industry. It can be used to make housings, heaters, radiators, etc. for electronic products. In the working environment of high temperature and high pressure, electronic products made of aluminum plate are very stable and can ensure the long-term service life of electronic products. Product ParametersProduct Description:We can manufacture the Aluminum sheet for you in cold rolled and hot rolled condition, our kind of products as follows:1000 Series: 1050, 1060, 1070, 1050A, 1350, 1145, 1035, 1100, 1200, 1235,2000 Series: 2011, 2014, 2014A, 2214, 2017, 2017A, 2117, 2218, 2618, 2219, 2024, 2124,3000 Series: 3103, 3004, 3005, 3105, 3003,5000 Series: 5005, 5019, 5050, 5251, 5052, 5154, 5454, 5554, 5754, 5056, 5356, 5456, 5082, 5182, 5083, 5A06 5A03 ,5183, 5086,6000 Series: 6101, 6101A, , 6005, 6005A, 6351, 6060, 6061, 6063, 6063A, 6070, 6181, 6082,7000 Series: 7003, 7005, 7020, 7022, 7050, 7075, 7475.Alloy: 1050, 1060, 1100, 3003, 5005, 5052, 5083, 5754, 6061Temper: H12. H14. H16. H18. H112. H22. H24. H26. H32. H34. H36. H38. H112, H111, H116, H321 O etc.Thickness: 0.2mm, 0.21mm, 0.22 mm, 0.25mm, 0.30mm, 0.35 mm, 0.4mm, 0.5mm, 0.6mm, 0.7mm, 0.8mm, 0.9mm, 1.0 mm, 1.1 mm, 1.2 mm, 1.3mm, 1.4mm, 1.5mm, 1.6mm, 1.7mm, 1.8mm, 1.9mm, 2.0mm, 2.1 mm, 2.2mm, 2.3mm, 2.5mm, 2.7mm, 2.8mm, 2.9mm, 3.0mm, 4.0mm, 6.0mm, 7.0mm, 8.0mm, 10.0mm, 12 mm 13mm, 14mm, 15mm, 16mm, 17mm, 18mm, 19mm, 20.0mm, 22mm, 25mm, 30mm, 35mm, 40mm, 45mm, 50mm, 60mm, 70mm, 80mm, 90mm, 100mm, 110mm, 120mm, 150mm, 180mm 200mm, 250mm, 300mm, 350mm, 400mmWidth: 1000mm, 1200mm, 1220mm, 1500mm, 2000mm, 2200mmLength: 1000mm, 2000mm, 2440mm, 2500m, 3000mm, 3600mm, 4000mm, 12000mmSpecification :TypeThickness(mm)Width(mm)Surface Alloy Grademill finished aluminum coil0.1-6.0mm20-2000mmmill finished1050,1060,1100,3003,3004,5052,5083,6061etc.aluminum coil with kraftpaper0.3-3.0mm1000,1200with kraftpaperDiamond aluminum coil0.3-2.0mm500-1250mmdiamond patternStucco aluminum coil0.2-2.0mm500-1400mm stucco patterncolor coated aluminum coil0.2-3.5mm170-1400mm color coated Chemical Composition:AlloySiFeCuMnMgCrNiZnTiZrAl10600.250.350.050.030.03----0.030.03 99.6%10500.250.40.050.050.05----0.050.03--99.5%11000.950.05~0.20.05------0.1----99%30030.60.70.05~0.21.0~1.5------0.1----Remainder30050.60.70.31.0~1.50.2~0.60.1--0.250.1--Remainder3105 0.6 0.7 0.3 0.3~0.8 0.2~0.8 0.2 -- 0.4 0.1 -- Remainder50520.250.40.10.12.2~2.80.15~0.35--0.1----Remainder50050.30.70.20.20.5~1.10.1--0.25----Remainder80110.5~0.90.6~1.00.10.20.050.05--0.10.08--RemaindenameAluminum sheet; Aluminum Plate Alloy Aluminum Plate; Alloy Aluminum Sheet; Aluminum Embossed Sheet 0.5~1mm;Aluminum Roofing Sheet 0.5~1mm1000 Series  1050, 1060, 1070 , 1050A , 1350 , 1145 ,1035 , 1100 , 1200 , 1235 ,2000 Series  2011 , 2014 , 2014A , 2214 , 2017 , 2017A , 2117 , 2218 , 2618 , 2219 , 2024 , 2124 ,3000 Series  3103 , 3004 , 3005 , 3105 , 3003,5000 Series 5005, 5019 , 5050 , 5251 , 5052 , 5154 ,5454 ,5554 ,5754 , 5056 , 5356 , 5456 , 5082 , 5182 , 5083, 5183 , 5086,6000 Series  6101 , 6101A , 6005 , 6005A , 6351 , 6060 , 6061 , 6063 , 6063A , 6070 ,6181 , 6082 ,7000 Series  7003 , 7005 , 7020 , 7022 , 7050 , 7075 , 7475Aluminum SheetAlloyThickness(mm)Width(mm)Length(mm)TemperDC or CC1050,1060,1070,1100,0.2-3.020-18501000-10000O,H12,H22,H14,H24,H16,H26,H18,H32DC, CC12353.0-150500-2200H112,H111DC3003,3004,3105,0.2-3.0300-18501000-10000O,H12,H22,H14,H24,H16,H26,H18,H32DC, CC3.0-150900-1900H112,H111DC5052 5083 5754 50050.2-3.0300-18501000-10000O,H12,H22,H14,H24,H16,H26,H18,H32,H36,H116,H112,H321DC3.0-400900-2600H112, H111DC6061 60631.0-400300-15001000-10000T6,T651DC,PackingExport standard wooden pallets packingApplicationMainly in Construction, decoration, PCB materials, cover material, LCD back panel, refrigeration, air conditioner, automobile, etcMOQ3-5MTKind attentionSpecifications can be customized as the customer ' s requirements Packaging & ShippingProduction workshopProduct packagingShippingShipped in 7 days after payment.Our AdvantagesCustomized service : 1.We are exporters and manufacturers of high-quality metal products in China.2. We can provide a complete set of metal products for different markets.3. We have the ability to serve customers with the most reliable quality and reasonable prices. 4. We can OEM and produce products based on the given design, and mass produce the designed goods.5. We regularly export to buyers around the world. These products are widely popular in the market.6. We hope to win more customers with high-quality products and reasonable prices.20Gp - 2.352(width) *2.385 ( Height ) * 5.90 ( Inside length ) Meter40Gp - 2.352(width) *2.385 ( Height ) * 11.8 ( Inside length ) Meter40HQ - 2.352(width) *2.69 ( Width ) * 5.90 ( Inside length ) MeterHow to make the order ?Δ First step , Please contact with our sales team , talked about the cargo details , if need sample , we can supply the sample for free ;Δ If the sample can reach to requirement , the client can sign the contract with our company;Δ Before shipment , client can inspect the cargo loading and seal the container , we also can accept inspection of the third party ( Such as SGS ,BV etc ) ;Δ After 5 days of shipment , we will send the documents of customs clearance to you ;Δ  After get the cargo , please give feedback to us ;Customer feedbackCompany Profile                  Shandong Standard Metal Products Co., Ltd. is a comprehensive company specializing in the production of alloy metal materials, X-ray protection equipment, and laser devices. At present, 70% of our products are exported to various parts of the world, and our key products have entered key fields and new industries such as nuclear power plants, petroleum, chemicals, shipbuilding, containers, railways, automobiles, urban light rail transportation, and large power plants.         Our business ideas are focus on high quality material , meantime supply good before -sale and after-sale service , give most benefit to our clients .Our well-equipped facilities and excellent quality control throughout all stages of production enable us to guarantee total customer satisfaction We have built strategic partnership with domestic huge manufacturer, Baosteel , TISCO, ZPSS, TPCO, . If you are interested in learning more details about our products, contact us freely. We wish to extend our warm welcome to our customers, old and new, both at home and abroad, to negotiate business with us on the basis of equality and mutual benefit.Customer visitsA Factory TourFAQQ1. Where is your factory ?A1: Our company's processing center is located in Shandong , China. Which is well equipped with kinds of machines, such as laser cutting machine, mirror polishing machine and so on.We can provide a wide range of personalized services according to the customers' needs.Q2. How do you control quality ?A2: First step , Please contact with our sales team , talked about the cargo details , if need sample , we can supply the sample for free ; If the sample can reach to requirement , the client can sign the contract with our company;Before shipment , client can inspect the cargo loading and seal the container , we also can accept inspection of the third party ( Such as SGS ,BV etc ) ;Q3. What are the advantages of your company ?A3: We have many professionals, technical personnel, more competitive prices and best after-dales service than other seamless lead product companies.Q4. Can you arrange the shipment ?A4: Sure we can help you with the shipment. We have forwarders who have cooperated with us for many yearsQ5. How about the delivery time ?A5: It is based on the order, After 5 days of shipment , we will send the documents of customs clearance to you ;After get the cargo , please give feedback to us ;  

OK ! We suggest you detail your product requirements and company information here.
Enter between 20 to 4,000 characters.
Your inquiry content must be between 20 to 4000 characters.