CNC Turret Punch Press Tools Cabinet Mold Cabinets for Murata Wiedemann Machine Tool¹

Product Description Product DescriptionMaterialPunch-body SKH51, Die DC53Heat treatmentHRC 60°-  62°Hits before regrinding ( for stainless steel )About 300000 hitsHits before regrinding ( for mild steel )About 500000 hitsAvailable TruPunch Machines ModelAMADA AE2510NT, AMADA 357, TAILIFT HP2500, MATE Ultra system, Prima Power E5X, LFK T3, Accurpress E2000, JFY ET-300, YANGLI T30, YAWEI HPH-30, FINN-POWER, KOMATS, STRIPPIT, DATONG PTC-LX230Forming toolsExtrusion tapping Tool, Extrusion Tool, Louver tool, Lance and Form tool, Cluster tool, Countersink tool, Half-cut tool, Plane positioning point tool, Knockout tool, Emboss Continuous tool, Thread screw tool, Center Point tool, HexLock tool, Bridge thread tool, MultiBend tool, Card guide tool, Hinge tool, Multi scribe tool, Logo tool, Ground symbol tool, Roller Rib tool, Roller Offset tool, Roller Shear tool, Roller Pincher tool, Roller Deburr toolOptionCoating with TICN or TinDelivery time3 - 10 Days Detailed PhotosTool Cabinet Parameter:Size length: 1500mm width: 540mm height: 1500mmInternal space: 1.2m 3Color: blue, redNet weight: 155 (kg)Tool storage1. Wipe the inside and outside of the upper mold sleeve with a clean rag, oil-proof, rust-proof, dust-proof, and prevent the mold from embrittlement and seizure;2. Be careful not to cause scratches or dents on the surface when storing. It is best to place it in a special mold management cabinet.Tool Preparation before use1. Thoroughly clean the upper mold sleeve before use, thoroughly clean each accessory before assembly, and add lubricant inside and outside;2. Carefully check the sliding fittings such as the punch, guide sleeve and lower mold for any bumps or burrs. If necessary, gently remove them with fine stone.3. When installing the large-position punch, adjust the direction, slide into the guide bushing, and lock the lifting bolt after the position is determined. It must be locked with special disassembly tooling.Tool installed into the turret1. Clean the inner wall of the turret hole and the keyway and clear the oil;2. Adjust the keyway of the upper mold guide sleeve to match the key of the turret hole;3. Insert the upper mold guide sleeve vertically into the turret hole. Be careful not to have any inclination. The upper mold guide sleeve slides into the turret hole by its own weight;4. If the upper mold guide sleeve is tilted to one side, use a soft material tool such as a nylon hammer to gently tap it, and repeat the tap until the upper mold guide sleeve slides into the correct position by its own weight.Note: Do not apply force to the outer diameter of the upper guide bushing. Only tap the top of the striker to avoid damage to the turret hole.Tool maintenance1. Please always check the performance of the spring. Excessive use of the spring will make the spring fatigue and replace it in real time.2. Disassemble the mold every month, remove the dirt from the punch, guide sleeve and lower mold with steam (chai) oil, wipe the oil and assemble it, so that the mold can have good lubrication performance. Tooling orderingPlease provide the following information when you purchase:CNC punch brandCNC punch press modelCNC punch die station structureThick tower 85 / thick tower 90 / thick tower MATE / thin tower 140 / Murata / thick tower heavy load / bus machine mold series(Mold height series or the outer diameter of our production data)The plate material thickness or clearanceOrdering parts: The whole package (eg die / die / back plate, etc.)Mold Specifications Shape Size: B-RE 30*5 (OB, SQ, RE)You shoot online transactions, you must provide detailed consignee and address phone, whether urgent.For example 1:AE2510-NTThick Turret 85Gap+0.3Full setB-RE 30*5For example 2:CP1500Thick Turret 90Gap+0.25Punch AssemblyD-OB Φ10*50For example 3:EM2510NTI TypeGap+0.3Upper and lower tooling stripperI-RO Φ15For example 4:M2048TE114 / VulcanGap+0.3Upper and lower toolingG-SQ 62*62For example 5:Busbar ProcessingMachine BM303Copper plate 0.3Full setB-SQ 20*20We hope that through online activities, to give you a better product and convenient service experience! Have any mold questions, can consult us, we will help you solve the problem the first time!Tooling Quoted priceMold height series or the outer diameter of our production data.Table of recommended die clearance(reference values)NCT drive typeMaterial type / thickness0.81.01.52.02.53.03.23.5HydraulicCold-rolled mild steel0.15-0.200.20-0.250.20-0.250.40-0.500.50-0.630.60-0.750.64-0.800.70-0.88Aluminum0.15-0.160.15-0.200.23-0.300.30-0.400.38-0.500.45-0.600.48-0.640.53-0.70Stainless steel0.20-0.240.25-0.300.38-0.450.50-0.600.53-0.750.75-0.900.80-0.960.88-1.05MechanicalCold-rolled mild steel0.150.15-0.180.18-0.270.24-0.360.30-0.450.36-0.540.38-0.580.42-0.63Aluminum0.150.15-0.160.15-0.240.20-0.320.25-0.400.30-0.480.32-0.510.35-0.56Stainless steel0.15-0.180.15-0.220.21-0.330.28-0.440.35-0.550.42-0.660.45-0.700.49-0.77 4.04.55.05.56.00.80-1.000.90-1.131.00-1.251.10-1.381.20-1.500.60-0.800.68-0.900.75-1.000.83-1.100.90-1.201.00-1.201.13-1.35---0.48-0.720.54-0.810.60-0.900.66-0.990.72-1.080.40-0.640.45-0.720.50-0.800.55-0.880.60-0.960.56-0.880.63-0.99---Material IntroductionPunch body material: SKH51SKH-51, alias high-speed steel, also known as steel or front steel, meaning quenching even in the air can be hardened when cooled, and very sharp. Chong stainless steel, skd series of more conventional mold, toughness and wear resistance are quite different.Die material: DC53DC53 is Japan's Datong special steel SKD11 to improve the new cold-work die steel, the technical specifications are contained in the Japanese Industrial Standards (JIS) G4404. It overcomes SKD11 high temperature tempering hardness and lack of toughness weaknesses, will be in the field of general and precision molds SKD11 fully replace the high strength and toughness of common cold die steel. Company ProfileDongguan Quapin Hardware Co.,Ltd.Dongguan Quapin Hardware Co., Ltd is a joint venture, it specialize in R&D, manufacturing both domestic and abroad CNC turret punch press tooling (NCT) mould. Quapin is Dongguan one of the most large-scale CNC turret punch press tooling manufacturer.QUAPIN is equipped with advance production equipment and inspection equipment. For example, CNC Center has CNC machining center, CNC computer lathe, sodick CNC wire-cut machine, CNC EDM machine, Professional internal grinding, Precision cylindrical grinder, Precision flat stone mill other other advanced processing equipment and optical projections, Hardness tester, Sand blasting machine, Marking machine and other high-precision testing equipment. After years of efforts, the company established scientific, high-efficiency, perfect management system as well as CAD/CAM/UG manufacturing capability.Quapin specializes in the research, development and manufacturing of CNC turret punch press molds. We provide one-on-one free technical service, lightning delivery and intelligent stocking; try our best to help the sheet metal manufacturing enterprises to increase production efficiency and minimize the processing cost of each product.We Qaupin products team silently in the tens of thousands of sheet metal business, elevator business, sheet metal machine tool business, the world's top 500 enterprises and other services;Quapin products in the mold to ensure quality, quality service at the same time, we constantly innovate! Adhering to do our best to help sheet metal production enterprises to improve production efficiency, the processing cost to a minimum!Packaging & ShippingFAQQ: Are you trading company or manufacturer ?A: We have 11 year experience in the production of the factory, we are Dongguan mold production base. For the customer we offer the price of competitive, professional production, adequate supply, high production efficiency, greatly expanding the interests of customers.Q: How long is your delivery time?A: Generally it is 3-7 days if the tools are standard. Or it is 15-20 days if the tools is special forming shape.Q: Do you provide samples ? is it free or extra ?A: We do not provide samples.Q: Do not receive the goods after payment or product delivery error how to do?A: The customer is paid to ****** One Touch's account at the time of payment, and ****** will guarantee a full refund when you encounter both casesQ: How is your after-sales service?A: After the delivery of mold quality problems, replacement(except man-made damage)Q: What is your terms of payment ?A: Payment<=1000USD, 100% in advance. Payment>=1000USD, 30% T/T in advance ,balance before shippment. 

OK ! We suggest you detail your product requirements and company information here.
Enter between 20 to 4,000 characters.
Your inquiry content must be between 20 to 4000 characters.