IPDB › China Industry › Metallurgy, Mineral & Energy › Alloy
Lork Hot Products AMS 5872/Mssr 7036/N07263 Nickel Alloy Rod for Low Temperature Combustors Haynes 263 Superalloy Bar1
Nickel Alloy, Haynes, Alloy 263
LORK GROUP CO., LTD
Preview:
Product Description Product Description IntroductionLORK is a super alloy manufacturer with 20 years of manufacturing experience. HAYNES 263 alloy (UNS N07263) is an age-hardenable nickel-cobalt-chromium-molybdenum alloy developed specifically to combine good age-hardened strength properties with excellent fabrication characteristics in the annealed condition. HAYNES 263 alloy exhibits excellent intermediate temperature tensile ductility, and is not normally subject to strain age cracking problems common for gamma prime strengthened alloys. Its strength at elevated temperature is not quite as high as materials such as HAYNES 282 alloy, Waspaloy alloy, or R-41 alloy. However, it is much easier to form or weld than Waspaloy alloy and R-41 alloy. Because HAYNES 282 alloy exhibits superior tensile, creep-rupture, and low cycle fatigue strength than HAYNES 263 alloy and has significantly greater fabricability than Waspaloy and R-41 alloys, it is replacing HAYNES 263 alloy in many applications.HAYNES 263 alloy is normally used for applications up to about 1650°F (900°C). Its oxidation resistance is comparable to that for other gamma-prime-strengthened superalloys.Haynes 263 Plate Applications? HAYNES C 263 is used in the following application areas:? Gas turbine hot section components such as medium temperature combustors? Aircraft turbine engine components? Land-based turbine components? Low temperature combustors? Transition linersFinishes#1 - Hot rolled annealed and descaled. It is available in strip, foil and ribbon. It is used for applications where a smooth decorative finish is not required.#2D - Dull finish produced by cold rolling, annealing and descaling. Used for deep drawn parts and those parts that need to retain lubricants in the forming process. #2B - Smooth finish produced by cold rolling, annealing and descaling. A light cold rolling pass is added after anneal with polished rolls giving it a brighter finish than 2D.#BA- Bright annealed cold rolled and bright annealed#CBA- Course bright annealed cold rolled matte finish and bright anneal#2 - Cold Rolled#2BA- Smooth finish produced by cold rolling and bright annealing. A light pass using highly polished rolls produces a glossy finish. A 2BA finish may be used for lightly formed applications where a glossy finish is desired in the formed part. Polished - Various grit finish for specific polish finished requirements.Cold FormingHaynes? 263 has excellent forming characteristics. The alloy has excellent ductility in the annealed condition, and thus may also be formed by cold working. Intermediate annealing in the temperature range from 1900 to 2000 °F may be needed for complex component forming operations. All hot or cold-worked parts should be annealed and rapidly cooled in order to restore the best balance of properties.Chemical Compositions Of Haynes 263 Nickel AlloyElementContent (%)Nickel, Ni52Chromium, Cr20Cobalt, Co20Molybdenum, Mo6Titanium, Ti2.4Iron, Fe0.7Aluminum, Al0.6Manganese, Mn0.6Silicon, Si0.4Copper, Cu0.2Carbon, C0.06Haynes 263 Mechanical Properties PropertiesMetricImperialTensile strength1050 MPa152.3 ksiYield strength635 MPa91.9 ksiElastic modulus221 GPa32.1 psiElongation at break35.70%35.70%Available Sizes And SpecificationsHaynes 263 available sizes and specificationsGradeHaynes 263Nickel plateThickness: 0.3mm - 150.0mmWidth: 1000mm - 3000mmNickel strip/ nickel foilThickness: 0.02mm - 16.0mmWidth: 5mm - 3000mmNickel coilThickness: 0.3mm - 16.0mmWidth: 1000mm - 3000mmNickel pipeOutside diameter: 6mm - 1219mmThickness: 0.5mm - 100mmNickel Capillary PipeOutside diameter: 0.5mm - 6.0mmThickness: 0.05mm - 2.0mmNickel barDiameter: Ф4mm - Ф600mmNickel wire rodDiameter:Ф0.01mm - Ф6mm Detection Processing Packaging & ShippingCompany ProfileFAQQ1: Do you accept the trial order ?A1: Yes,if we have the exactly size in stock.we can delivery even 1 piece/meter .Q2: Can I have free sample before making orders?A2: Yes,we can supply free sample as requirement,but buyer needs to pay the freight charges ,the freight fee will return to buyer after making order.Q3: How do you control the quality ?A3: MTC and PMI will be sent before shipment,any 3rd party inspection if need .Q4: How about your delivery time ?A4: Generally delivery time is 15 working days .Q5: How can I quickly get the price list ?A5: Directly click "chat now" or send us email with detail specifications,you will get the official price list in 1 hour .
Purchasing Agent
Note: Send your message to supplier or manufacturer.
Welcome to our Professional and comprehensive procurement services...
Message:
OK ! We suggest you detail your product requirements and company information here.
Enter between 20 to 4,000 characters.
Your inquiry content must be between 20 to 4000 characters.