CIPDB › China Industry › Instruments & Meters › Weighing & Measuring Apparatus

Thermo Fisher Scientific Mt9000 Mt9301 Integrator¹

Preview:

Product Description Standard FeaturesThe Micro-Tech has many hardware and software features. The standard features of the Micro-Tech are listed below.Menu-driven scroll entries on a four line display.Four LED status indicators.Audit trail.Automatic zero and span calibration.Auto zero tracking. (Where applicable)Several software options that may be turned on by keypad entry or by installing optional plug-in PC boards.Optically coupled digital inputs and outputs.Alarms and failure detection.Communication standards such as RS232C, RS485, and networking multi-drop.Allen-Bradley DF1 and Modbus RTU.Ethernet/IP and Modbus/TCPInputs and OutputsThe standard Micro-Tech configuration is as follows. For more information about the Micro specific model reference manual -Tech's communication protocols, see . the USB port.Two serial communication ports.Two digital inputs on the Motherboard.One DC output from the mother board (J29).Ethernet TCP/IP.Four circuit board expansion slots that can accommodate the following boards, if needed.Three programmable digital inputs on plug-in card.Four programmable digital outputs on a plug-in card.Single channel current output boardDual channel current output, analog input board (2 analog in and 2 analog out)8 digital inputs/8 digital outputs boardSerial communication boardProfibus-DP boarMicro-Tech Menus and Functions Each capable of performing all of the necessary measuring functions. All of Micro-Tech has been designed for a specific application and is the required functions are resident in the software of the microprocessor. Optional functions are automatically turned on when the relevant hardware is installed, or after the operator has selected them through the keypad. Setup of the Micro-Tech is easy and is performed from the keypad on the front of the device. The setup parameters may be divided into the following main groups.Menu 1: CalibrationMenu 2: Set-upMenus 3-6: Options set-upMonitoring FunctionsThe Integrator includes internal diagnostics that generate alarms in case of hardware failures or programming errors. Alarms are visible on the display and can be acknowledged and reset through keyboard, digital input or serial line. Alarms can be delayed to avoid intervention in case of short time peaks. You can program each individual alarm to operate as a simple alarm, a shut down function, or the alarm can be ignored. Two LED's indicate the cumulative status of alarms and shut-down. Digital outputs are also provided for the following: Hardware failure Alarm cumulativeShut down cumulativePrint Functions Timed or command prints can be obtained by connecting a serial printer to the Comm output on the motherboard, or an optional communication board. Data may also be downloaded to a USB memory device. Time and date are permanently stored in the battery-backed memory. The integrator Set-Up, Totals, Zero results, and Audit Trail of the instrument can be printed.Functions There are two communication ports on the Motherboard. Comm A is RS232C/RS-485 (jumper selectable), isolated. Comm B is RS-485 only, non-isolated. One additional communication board may be installed. For detailed descriptions of communication protocols, see the specific model reference manual. There are three types of standard communication functions, as described below.Serial Communications The communication protocol allows a remote intelligent device to read the contents of the registers and write to some registers. During the communication activity, the Micro-Tech always acts as a Slave, meaning it responds to a request from a Master device on the line, but never attempts to send messages out. One electrical interface may be selected and accessed through one communication port.Field Bus I/O Profibus-DP I/O communication protocol board is typically used to transfer I/O images between a main PLC and the remote devices (normally remote I/O racks-rack adapters) or to transfer (read and write blocks of data with intelligent remote devices (node adapters), the Micro-Tech in this case. The Remote I/O is a typical master/slave communication where the main PLC is the master or scanner and the remote devices are slaves or adapters.Ethernet Port The Micro-Tech has a built-in Ethernet port. Communications protocols Ethernet/IP and Modbus/TCP can be used. The MicroTech is a Slave device only, and cannot initiate messages.

× More Keyword ..

× More Menu ..

×

Manufacturing & Processing Machinery

×

Industrial Equipment & Components

×

Tools & Hardware Products