CIPDB › China Industry › Instruments & Meters › Meter for Liquid & Gas
China, Chinese WiFi 4G GPRS Wholesales Remote Monitoring System for Smart Water Meter1 Industrial Products Supplier Manufacturer Details, price list catalog:
China Products Details Supplier Manufacturer price list catalog
Meter for Liquid GasSmart Water Meter SuppliersSmart Water Meter Manufacturers
Tai'an Desheng Information Technology Co., Ltd.
Preview:
Product Description 1. Technical parametersItemsParameterNominal caliberDN15DN20DN25Range RatioR100 Q4(m3/h)3.12557.875Q3(m3/h)2.546.3Q2(m3/h)0.040.0640.1008Q1(m3/h)0.0250.040.063Temperature ClassT30/T50/T90Overload flow (Q4) - The water meter is required to meet the maximum allowable error requirements in a short period of time, and then maintain the maximum flow rate of the metering characteristics under rated operating conditions.;Common flow rate (Q3) - the maximum flow rate under rated working conditions. Under this flow rate, the water meter should work normally and meet the maximum allowable error requirements;Boundary flow (Q2) - the flow that occurs between the common flow Q3 and the minimum flow Q1, dividing the flow range into two areas: "high zone" and "low zone" with specific maximum allowable errors;Minimum flow rate (Q1)-the minimum flow rate that requires the water meter's indication to comply with the maximum allowable error;Indication error: Within the water temperature range of 0.1oC to 50oC, the maximum allowable error of the water meter is ±2% in the high area (Q2≤Q≤Q4) and (±5%) in the low area (Q1≤Q<Q2).2.Dimensions of wireless remote water meter CaliberLWH2Thread Connection Pipe ?Thread Connection Case ?DN1516590150R 1/2G 3/4 BDN2019590152R 3/4G 1 BDN25225104175R 1G1 1/4 BTemperature LevelT30/T5/T90 (Standard Default T30)Max Work Pressure1.6MPaWork Environment-10oC-55oC; ≤100%RHUp stream Flow Field Sensitivity LevelU10Down stream Flow Field Sensitivity LevelD5Climate and mechanical environment gradeEElectromagnetic compatibility classB1Power SupplyDC 2.8V-3.6VPressure Loss≤0.063MPAProtection LeveIP683.Installation, use and maintenance methods 3.1. A wireless remote water meter of appropriate caliber should be selected based on the pipe diameter and water consumption at the installation location.3.2. The installation location should avoid exposure, freezing, pollution, moisture and flooding to facilitate disassembly and meter reading. During the freezing period, in addition to wrapping the water meter and water pipes, close the inlet valve of the water meter and open the outlet valve and faucet when not in use. This can prevent the water meter from being damaged due to freezing expansion. It is recommended to install it in a special water meter box.3.3. The water meter should be installed horizontally, with the letter facing up and the arrow direction in the same direction as the water flow.3.4. It is necessary to wash away the gravel, sediment and other debris in the newly installed pipes before installing the water meter to avoid causing water meter failure.3.5. For accurate measurement, the faucet should be higher than the water meter.3.6. If the water meter is installed at the boiler water inlet pipe, prevent the backflow of hot water from scalding the water meter.3.7. The water meter should not be directly connected to the pipeline. The water meter and the pipeline should be connected through pipes, sealing washers, and connecting nuts. When disassembling the water meter, do not use hard plates to avoid twisting the case.3.8. The water meter should be protected from excessive stress caused by pipes and fittings. If necessary, the water meter should be installed on a base or bracket.3.9. Valves should be installed before and after the water meter to facilitate maintenance and replacement.3.10. Do not install the water meter in a metal water meter box to avoid signal shielding and preventing remote meter reading.4. AMR Reading We provide total solutions for smart flow metering, control, telemetry and smart water meter reading system. Q1:Can I request to advance the shipment?A: It should be depends on whether there is sufficient inventory in our warehouse.Q2: Can your company print our brand logo on your products?A: With the customer's permission, our factory can print the customer logo on the product. However, the customer needs to provide us with a logo authorization so that we can print the customer logo on the product.Q3: What are your quality control procedures?A: We adhere to strict quality control procedures, from product design to the end of the production process, using the most advanced quality control equipment, so that all processes are always in the best state of control.Q4: Can I request a change in packaging and shipping?A: Yes, we can change the packing and shipping method according to your requirements, but the cost and difference incurred in the meantime will be your responsibility.Q5: What are your payment terms?A: T/T, L/C, and othersQ6: What is the standard lead time for each order?A: It depends on the number of orders you need to purchase. Normally, we complete the order within 15 days.
Purchasing Agent
Note: Send your message to supplier or manufacturer.
Welcome to our Professional and comprehensive procurement services...