CIPDB › China Industry › Instruments & Meters › Heating, Refrigeration & Temperature Control
1800 U Shape 4/9 Electric Furnace Heater Lab Factory Low Price Resistance Long Use Life High Quality Molybdenum Disilicide Rod Mosi2 Heating Element Heater1
Heating Refrigeration Temperature ControlFurnace HeaterElectric Heater
Henan HIQ Furnace Co., Ltd
Preview:
Product Description Product DescriptionMolybdenum disilicide(MoSi2) heating element/heater:Mosi heating element is a kind of resistance heating element basically made of pure molybdenum Disilicide. In oxidizing atmosphere, a layer of compact quartz protective film is formed on the surface of Mosi 2 element owing to the high temperature combustion, which prevents Mosi 2 from continuously oxidizing.In oxidizing atmosphere, its Max temperature can reach 1800 c and its applicable temperature is 500-1700. It can be widely used in such applications as sintering and heat treatment of ceramics, magnet, glass, metallurgy, refractory etc. the commercial name of our Mosi 2 heating element is KERONE Mosi 2 Heating Element.Product ParametersMolybdenum disilicide(MoSi2) heating element/heater:1. According to temperature: 1700C 1800C 1900C2. According to Shape: U, W, I, U type L shape, W type L shape, Spiral types.Molybdenum disilicide(MoSi2) heating element/heater standard sizeM1700 type (D1/D2): dia3/6, dia4/9, dia6/12, dia9/18, dia12/24M1800 type (D1/D2): dia3/6, dia4/9, dia6/12, dia9/18, dia12/24M1900 type (D1/D2): dia3/6, dia4/9, dia6/12, dia9/18, dia12/24 Chemistry CharacterMoSi2 heating element is used in the high temperature under oxidizing atmosphere. It will form the SiO2 film which can keep the element from being melted. During the oxidizing process, the SiO2 protecting film is formed again when the element continues to be used. The MoSi2 heating element must not be used in the temperature between 400C and 700C for a long time, otherwise the element will be cremated under the strong oxidizing function in the low temperature.Physics characters of Molybdenum disilicide(MoSi2) heating element/heater:Bulk densityBending strengthHardnessApparent porosityDrawing water rateThermal elongation5.5~5.8g/cm320MPa(20oC)(hv)570kg/mm20.5~2.0%0.5~2.0%4%Recommend surface load:Furnace Temp(°c)14001500160016501700Surface load of hot zone(W/cm2)<18<15<12<10<8The influence of operation temperature on the heater surface in a different atmosphere:AtmosphereThe Maximum Using Temperature of Elements17001800No2 ,Co2 ,O2 ,Air1700°C1800°CHe ,Ar ,Ne1650°C1750°CSo21600°C1700°CCO ,H21500°C1600°CWet H21400°C1500°CDry H21350°C1450°C How to orderWhen you place order, plz inform us below data:Material Grade: 1700C / 1800C / 1900CDiameter: D1/D2, mmHot zone length: Le, mmCold zone length: Lu, mmShank Space: A, mmOrder Sample: diaD1/D2 x Le x Lu x ADetailed PhotosInstallation Instructions1800 U Shape 4/9 Electric furnace lab industry factory low price resistance long use life high quality heater Molybdenum Disilicide Rod Mosi2 Heating ElementThe radiation coefficient of silicon molybdenum rods is slightly softened at high temperatures (above 1500 degrees), and hard and brittle at low temperatures. In order to avoid stress during temperature changes and facilitate the thermal expansion and contraction of components, it is best to use a free vertical hanging installation method. The dismantling and replacement of lifting components is also relatively convenient, without waiting for the furnace to cool down, and can be heat exchanged.When hanging silicon molybdenum rods, the following precautions must be taken:1. The furnace lining material should use corundum bricks, and the mass fraction of Fe2O3 should be less than 1%, because it interacts with the protective film to form a molten silicate, thereby accelerating the damage of the components.2. The hot furnace gas leaked from the cold end not only increases the heat loss of the furnace, but also may burn out the conductive tape clamps and lead clamps. Therefore, it is best to use asbestos clamps.3. As silicon molybdenum rods are brittle materials with low bending strength and cannot withstand impact, protective measures should be taken during installation to prevent breakage. When connecting the conductive tape, the asbestos clamp (or ceramic clamp) must be installed first, and excessive force should not be applied when clamping.4. Install the silicon molybdenum rod into the plug brick. In order to avoid the mechanical stress caused by loading and unloading movement, the plug brick shall be a separate brick made of foam corundum brick.Packaging & Shipping Our Advantages1. We provide special designed Molybdenum Disilicide (MoSi2) heating element according to customer needs, enabling an optimized element design for each particular application. 2. Delivery time: 7days after receipt deposit.3. Package: Synthetic Wooden Box with Cardboard Box and sponge We also received OEM service; the package can be designed according to your requirements.Our Service1. Timely response, Timely response to your inquiry, multiple choice recommendations based on your demand, quickly respond mails and provide solutions. 2. Sample evaluationSample and trial order is accepted for the quality evaluation. 3. Strict quality controlArrange production on time and control quality strictly. 4. Shorter delivery time.Book the earliest vessel or plane to guarantee the delivery time. 5. Professional ServicesProvide all the detailed news and pictures from order to delivery;Offer relative export documents and original certificate if needed;Warm and considerable after-sale service We also received OEM service; the package can be designed according to your requirements.Shipping: By vessel or by plane from any Chinese port, Samples can be delivered by International express.
Purchasing Agent
Note: Send your message to supplier or manufacturer.
Welcome to our Professional and comprehensive procurement services...
Message:
OK ! We suggest you detail your product requirements and company information here.
Enter between 20 to 4,000 characters.
Your inquiry content must be between 20 to 4000 characters.