CIPDB › China Industry › Instruments & Meters › Electrical Control System
China, Chinese Intelligent Controls Canopen/Ethercat/Modbus Network Servo Motor Control System Servo Motors and Drives for 3 Axis Servo Controller1 Industrial Products Supplier Manufacturer Details, price list catalog:
China Products Details Supplier Manufacturer price list catalog
Electrical Control SystemCanopen Servo DrivesEthercat Servo Drives
Wuhan Sine Electric Technology Co., Ltd
Preview:
Product Description Intelligent Controls Canopen Network servo motor control system servo motors and drives for 3 Axis Servo ControllerProduct DescriptionHigh-speed response performance?Up to 1.0KHz speed frequency response.?Shortened positioning time.?High-speed and high-accuracy real-time synchronouscommunication on basis of parallelized system design.High-accuracy positioning?Encoder of 17 bit incremental and 23 bit absolute value,with the powerful control performance, can make thepositioning accuracy less than 5 encoder pulses.Abandant product series?Analog & pulse standard type and network type withEtherCATor CANopen or RS485 protocol supported;?2500 ppr or serial type with17 bit incremental or 23 bit absolute values encoder availableSmall Size?Size similar to Panasonic A6 series drive, matched with SINEE SES servo motor, can help to minimize the system volume.Intelligent controls?Intelligentized resonance suppressionThe system has four (4) high-frequency resonance suppressionnotch filters, two (2) of them are the FFT-based ones; the othersare manual ones.Synchronously the vibration suppression filters are providedto minimize the vibration of long arm machine.?Control gain switchover functionsThe control loop structure on the basis of PDFF may reduceovershooting efficiently.The parameter self-adjustment on the basis of inertiamay enhance the site adaptability.High reliability?Complete protection function and EMC designProtection function design on the basis of overall reliability of motor and driver;EMC design on the basis of graded optimization and system adaptability.?High-performance motor material and technology ensure the system to run reliablyContaining dysprosium-neodymium-ferroboron magnetic steel, high-strength shaft,Tamagawa encoder, large-size bearing, encapsulated by resin.Product ParametersItemSpecificationInput/output signalDigital input Modifiable signal distribution8-way DIServo enabled, fault resetting, position pulse error counter clearing, speed command direction selection, position/speed multi-stageswitch, zero-position fixing enabled, internal command triggering, control mode switch, pulse Inhibited, positive drive Inhibited,Negative driveInhibited, second torque limit, positive inching, negative inching, othersDigital output Modifiable signalfrequency dividing4-way D0Servo ready, brake output, motor rotary output , zero-speed signal, speed proximity, speed arrival,position proximity, position arrival, torque limit, speed limit, warning output, fault output, othersInternal functionsOverrun prevention functionP-OT, N-OT take effect, deceleration stopLED display5-bit LED display: main circuit CHARGEProtection functionOvervoltage, undervotage, overcurrent, overspeed, IGBT overheat, overload, encoder abnormality,large position error, EEPROM fault, othersOthersTwo-stage gain switch, automatic gain adjustment, 4 groups of alarm records, JOG operationCommunication functionsCommunication modeRS232,RS485, CANopen Synchronizing cycle: 1ms or its integral multipleSupporting the following operation modes:Profile position modeProfile velocity modeProfile torque modeHoming modeInstallation InstructionsItemDescriptionAntirust treatmentBefore installation, please wipe off the "rust inhibitor" on the extension of the servo motor shaft before relevant antirust treatment.Notes for encoders?The shaft extension shall not be impact during installation, otherwise the encoder inside will be cracked. Pulley installation?When installing pulleys on a servo motor shaft with a keyway, use screw holes at the shaft end. In order to install the pulley, first insert the double-headed nail into the screw hole of the shaft, use a washer on the surface of the coupling end, and gradually fasten the pulley with a nut.?For servo motor shaft with a keyway, install it with the screw hole at shaft end. For a shaft without keyway, wear coupling or similar methods can be adopted.?When the pulley is removed, a pulley remover should be used to prevent impact on the bearing.?In order to ensure safety, a protective cover or similar device shall be installed in the rotating area.Centering?Please use a coupling to connect the device with the machine and keep the axis of the servo motor in a straight line with that of the machinery. The radial runout of the coupling should not be greater than 0.03 mm. If centering is not sufficient, vibration will occur, which may damage bearings, encoders, etc.Installation direction?Servo motor can be installed in a horizontal or vertical direction. Please do not install the device obliquely, otherwise it may cause wearing of motor bearing.Countermeasures for oil and waterFor use in places with water dripping, please confirm the protection rating of the servo motor before use (except the shaft penetration part). For use in places where oil drips to the shaft penetration part, please be sure to use servo motors with oil seals.Service conditions for servo motors with oil seals:?Please make sure that the oil level is lower than the lip of the oil seal during use.?Please use the oil seal in a state where the oil spatter can be kept in a good degree.?When the servo motor is installed vertically upward, please be careful to prevent oil accumulation on the oil seal lip.Cable stress conditionDo not bend the cables excessively or apply tension to them, especially for the 0.14 mm2 or 0.2 mm2 core wires of the encoder signal cables, which is very thin. So please do not stretch them too tightly during wiring and use.When installing in the tow chain, high-flexibility tow chain cables must be selected.Connector handlingFor the connector part, please pay attention to the following:?When connecting a connector, please make sure that there is no foreign matter such as garbage or metal debris in the connector.?When connecting the connector to the servo motor, be sure to connect from the side of the main circuit cable of the servo motor first, and the main cable must be reliably grounded. Otherwise, the encoder may fail due to the potential difference with PE.?When wiring, please make sure the pins are arranged correctly.?The connector is made of resin. Do not apply impact to the connector, otherwise it may be damaged.?Always hold the main body of the servo motor during handling while the cables remain connected. Otherwise, the connector may be damaged or the cables may be broken.?If a cable needs to be bent, due care should be taken during wiring so as not to cause pressure or tension on the connector, otherwise damage or poor contact of the connector may be caused.Company Profile
Purchasing Agent
Note: Send your message to supplier or manufacturer.
Welcome to our Professional and comprehensive procurement services...