CIPDB › China Industry › Instruments & Meters › Electrical Control System

New Type Simatic Et 200sp Digital Output Module PLC Dq 4X 24VDC/2A 6es7132-6bd20-0ba0¹

Preview:

Product Description NEW type Simatic Et 200sp Digital Output Module PLC Dq 4X 24VDC/2A 6es7132-6bd20-0ba0Overview4, 8 and 16-channel digital output (DQ) modulesApart from the standard type of delivery in an individual package, selected I/O modules and BaseUnits are also available in a pack of 10 units. The pack of 10 units enables the amount of waste to be reduced considerably, as well as saving the time and cost of unpacking individual modules.For different requirements, the digital output modules offer:Function classes Basic, Standard, High Feature and High Speed as well as fail-safe DQ (see "Fail-safe I/O modules")BaseUnits for single or multiple-conductor connection with automatic slot codingPotential distributor modules for system-integrated expansion with potential terminalsIndividual system-integrated potential group formation with self-assembling voltage busbars (a separate power module is no longer required for ET 200SP)Option of connecting actuators with rated load voltages of up to 120 V DC or 230 V AC and load currents of up to 5 A (depending on module)Relay modulesNO contact or changeover contactfor load or signal voltages (coupling relay)with manual operation (as simulation module for inputs and outputs, jog mode for commissioning or emergency operation on failure of PLC)PNP (sourcing output) and NPN (sinking output) versionsClear labeling on front of moduleLEDs for diagnostics, status, supply voltage and faultsElectronically readable and non-volatile writable rating plate (I&M data 0 to 3)Extended functions and additional operating modes in some casesMSO operating mode (simultaneous reading of output data from as many as three other PLCs)Pulse width modulation mode (output value as pulse-pause ratio of between 0.0% and 100.0% for controlling the output current)Oversampling operating mode (n-fold equidistant output of digital values within a PN cycle for the precise time control of an output or a sequence of output values)Isochronous mode (simultaneous equidistant output of all output channels)Output of substitute value in the event of interruptions to communication (0, 1 or last value retained)Re-parameterization during operationFirmware updateValve control (output signal does not switch automatically after a set pickup time to a current-saving PWM output)Diagnosis of wire break and short-circuit (on channel or module basis)Value status (optional binary validity information of the output signal in the process image)Supports the PROFIenergy profileOptional accessoriesLabeling strips (film or card)Equipment labeling plateColor-coded label with module-specific CC codeShielding terminalA quick and clear comparison of the functions of the different DQ modules is offered by the TIA Selection Tool.Overview of digital output modulesDigital outputPUArticle No.CC codeBU typeDQ 16 x 24 V DC/0.5 A BA16ES7132-6BH00-0AA0CC00A0DQ 16 x 24 V DC/0.5 A BA106ES7132-6BH00-2AA0CC00A0DQ 16 x 24 V DC/0.5 A ST16ES7132-6BH01-0BA0CC00A0DQ 16 x 24 V DC/0.5 A ST106ES7132-6BH01-2BA0CC00A0DQ 8 x 24 V DC/0.5 A SNK BA16ES7132-6BF61-0AA0CC01A0DQ 8 x 24 V DC/0.5 A BA16ES7132-6BF01-0AA0CC02A0DQ 8 x 24 V DC/0.5 A BA106ES7132-6BF01-2AA0CC02A0DQ 8 x 24 V DC/0.5 A ST16ES7132-6BF01-0BA0CC02A0DQ 8 x 24 V DC/0.5 A ST106ES7132-6BF01-2BA0CC02A0DQ 8 x 24 V DC/0.5 A HF16ES7132-6BF00-0CA0CC02A0DQ 8 x 24 V DC/0.5 A HF106ES7132-6BF00-2CA0CC02A0DQ 4 x 24 V DC/2 A ST16ES7132-6BD20-0BA0CC02A0DQ 4 x 24 V DC/2 A ST106ES7132-6BD20-2BA0CC02A0DQ 4 x 24 V DC/2 A HF16ES7132-6BD20-0CA0CC02A0DQ 4 x 24 V DC/2 A HSWith three operating modes:Fast isochronous DQ with valve controlPulse width modulationOversampling16ES7132-6BD20-0DA0CC02A0DQ 4 x 24 ... 230 V AC/2 A ST16ES7132-6FD00-0BB1CC41B0, B1DQ 4 x 24 ... 230 V AC/2 A ST106ES7132-6FD00-2BB1CC41B0, B1DQ 4 x 24 ... 230 V AC/2 A HFWith two operating modes:DQPC: Power control via phase angle, half-wave or full-wave control16ES7132-6FD00-0CU0CC20U0RQ 4 x 24 V UC/2 A CO ST16ES7132-6GD51-0BA0--A0RQ 4 x 120 V DC-230 V AC/5 A NO ST16ES7132-6HD01-0BB1--B0, B1RQ 4 x 120 V DC-230 V AC/5 A NO ST106ES7132-6HD01-2BB1--B0, B1RQ MA 4 x 120 V DC ... 230 V AC/5 A NO ST16ES7132-6MD00-0BB1--B0, B1ApplicationDigital actuators (magnetic valves, contactors and signal lamps, etc.) can be controlled by means of the digital output modules.DesignUsable BaseUnits (BU)BaseUnits with an appropriate number of terminals are available for single or multi-conductor connection.All variants that correspond to the BU type of the I/O module used can be used as BaseUnits (see Selection and ordering data). The BaseUnits that can be used for the respective module are noted on the front side of the module.Potential distributor modulesWith the new potential distributor modules for SIMATIC ET 200SP, additional potentials required within an ET 200SP station can be set up quickly and in a space-saving manner. Due to the free combinability of PotDis-BUs and PotDis-TBs, the potential distributor modules allow a large number of design variants and thus simple adaptation to individual needs. Within the station, existing potentials can be multiplied or even new potential groups can be formed. With 36 terminals per 15 mm width, the PotDis modules require very little space without compromising on the conductor cross-sections (maximum 2.5 mm2). They allow the connection of voltages up to 48 V DC with a maximum current carrying capacity of 10 A, and with the PotDis-TB-BR-W even up to 230 V AC/10 A as well as the possibility to connect a protective conductor.Typical applications for the PotDis modules in connection with DQ modules are:3-wire connection of actuators (signal, mass, PE) for 16-channel output modulesSupply of supply voltage for actuatorsPotential group formationA light BU separates the self-assembling, internal voltage buses (P1, P2, AUX) and thus opens a new potential group. The supply voltage of a potential group must be fed in at the light BU of this potential group.A dark BU forwards the supply voltage of the adjacent light BU on the left via the self-assembling voltage buses P1, P2 and AUX. A new infeed is therefore only required on the next light BU to the right. The setting of a further light BU is required whenevera new potential group is to be formed (for example, for isolating the supply voltage from module groups) orthe maximum current simultaneously required by the potential group exceeds the permissible limit of 10 A.Color identification of the terminalsThe potentials at the terminals of the BaseUnit are defined by the inserted I/O module in each case. To prevent wiring faults, the potentials of the terminals can optionally be identified by means of module-specific color-coded labels. The color-coded label that matches the respective I/O module is defined by the color code CCxx of the I/O module. This color code is also printed on the front of the module.In BaseUnits with the additional ten internally jumpered AUX terminals, these can also be identified with color-coded labels. For the ten AUX terminals, color-coded labels are available in red, blue, and yellow/green.LabelingLabeling stripsLabeling strips can be inserted on the front of the interface modules or I/O modules and individually labeled via STEP 7, macros, etc. No special additional holder is required. If required, they can be easily replaced with the component.Equipment labeling platesEquipment labeling plates enable the equipment to be easily identified (e.g. compliant with EN 81346). They are easily plugged onto the required component (interface modules, I/O modules and BaseUnits) and when required, they can be easily replaced with the component.The following labeling components are available:Film labeling strips, light-gray, roll with 500 strips, perforated, for thermal transfer printersFilm labeling strips, yellow, roll with 500 strips, perforated, for thermal transfer printersCard labeling strips (180 g/m2), light gray, ten DIN A4 sheets with 100 strips each, perforated, for laser printerCard labeling strips (180 g/m2), yellow, ten DIN A4 sheets with 100 strips each, perforated, for laser printerEquipment labeling plates, white, ten sheets each with 16 labels, for thermal transfer card printers or labelsSystem-integrated shield connectionFor the space-saving and EMC-optimized connection of cable shields, a shield connection is available that is quick and easy to mount. This consists of one shield connection element that can be plugged onto the BaseUnit and one shield terminal for each module. The low-impedance connection to the functional ground (DIN rail) is achieved without any additional wiring by the user.Data sheet 6ES7132-6BD20-0BA0SIMATIC ET 200SP, digital output module, DQ 4x 24VDC/2A Standard, suitable for BU type A0, Color code CC02, Module diagnosticsGeneral informationProduct type designationDQ 4x24 V DC/2 A STHW functional statusFrom FS08Firmware versionV1.1FW update possibleYesusable BaseUnitsBU type A0Color code for module-specific color identification plateCC02Product functionI&M dataIsochronous modeYes; I&M0 to I&M3NoEngineering withSTEP 7 TIA Portal configurable/integrated from versionV11 SP2 / V13STEP 7 configurable/integrated from versionV5.5 SP3 / -PCS 7 configurable/integrated from versionV8.1 SP1PROFIBUS from GSD version/GSD revisionGSD Revision 5PROFINET from GSD version/GSD revisionGSDML V2.3Operating modeDQYesDQ with energy-saving functionNoPWMNoOversamplingNoMSONoSupply voltageRated value (DC)24 V19.2 V28.8 V Yespermissible range, lower limit (DC)permissible range, upper limit (DC)Reverse polarity protectionInput currentCurrent consumption, max.60 mA; without loadoutput voltage / headerRated value (DC)24 VPower lossPower loss, typ.1 WAddress areaAddress space per moduleAddress space per module, max.1 byte; + 1 byte for QI informationHardware configurationAutomatic encoding Mechanical coding elementType of mechanical coding elementYesType ASelection of BaseUnit for connection variants1-wire connection2-wire connection3-wire connection4-wire connectionBU type A0 BU type A0BU type A0 with AUX terminals or potential distributor moduleBU type A0 + Potential distributor moduleDigital outputsType of digital outputSource output (PNP, current-sourcing) 4No Yes Yes Yes2.8 to 5.2 A Typ. L+ (-50 V)YesNumber of digital outputsCurrent-sinkingCurrent-sourcingDigital outputs, parameterizableShort-circuit protectionResponse threshold, typ.Limitation of inductive shutdown voltage toControlling a digital inputSwitching capacity of the outputswith resistive load, max.on lamp load, max.2 A10 WLoad resistance rangelower limitupper limit12 ohm3 400 ohmOutput currentfor signal "1" rated valuefor signal "0" residual current, max.2 A0.1 mAOutput delay with resistive load"0" to "1", typ."0" to "1", max."1" to "0", typ."1" to "0", max.50 μs50 μs100 μs100 μsParallel switching of two outputsfor upratingfor redundant control of a loadNoYesSwitching frequencywith resistive load, max.with inductive load, max.on lamp load, max.100 Hz2 Hz10 HzTotal current of the outputsCurrent per channel, max.Current per module, max.2 A8 ATotal current of the outputs (per module)horizontal installationup to 40 °C, max.up to 50 °C, max.up to 60 °C, max.8 A6 A4 Avertical installationup to 30 °C, max.up to 40 °C, max.up to 50 °C, max.up to 60 °C, max.8 A6 A4 A4 ACable lengthshielded, max.unshielded, max.1 000 m600 mInterrupts/diagnostics/status informationDiagnostics functionYesYesSubstitute values connectableAlarmsDiagnostic alarmYesDiagnoses Monitoring the supply voltageWire-breakShort-circuitGroup errorYesYes; Module-wise Yes; Module-wise YesDiagnostics indication LEDMonitoring of the supply voltage (PWR-LED)Channel status displayfor channel diagnosticsfor module diagnosticsYes; green PWR LED Yes; green LEDNoYes; green/red DIAG LEDPotential separationPotential separation channelsbetween the channelsbetween the channels and backplane busbetween the channels and the power supply of the electronicsNo Yes NoIsolationIsolation tested with707 V DC (type test)Standards, approvals, certificatesSuitable for safety functionsNoYes; see FAQ Entry ID: 39198632Suitable for safety-related tripping of standard modulesHighest safety class achievable in safety modePerformance level according to ISO 13849-1SIL acc. to IEC 61508PL dSIL 2Ambient conditionsAmbient temperature during operationhorizontal installation, min.horizontal installation, max.vertical installation, min.vertical installation, max.-30 °C; < 0 °C as of FS08 60 °C-30 °C; < 0 °C as of FS0850 °CAltitude during operation relating to sea levelInstallation altitude above sea level, max.5 000 m; Restrictions for installation altitudes > 2 000 m, see manualDimensionsWidth15 mm73 mm58 mmHeightDepthWeightsWeight, approx.30 g Shenzhen Aimiqu Technology Co., Ltd.Shenzhen Aimiqu Technology Co., Ltd. was established in 2016 and is located in Bao'an District, Shenzhen. The company has professional technical personnel, focusing on the development and practice of automation, digitalization, networking and intelligence in the industrial field. Provide products, solutions and services for the majority of industrial enterprises and governments with automation systems, digital factories, industrial Internet and industrial big data intelligent integration, and strive to become a domestic intelligent manufacturing overall solution provider.Shenzhen Aimiqu is a factory specializing in production & sales & research in electric cabinet.And Shenzhen Aimiqu is a specializing in sales original PLC&pneumatic products & Industrial Control Instrumentation including Siemens,Fairchild and ST etc and related accessories .In PLC&Pump Valve & Pneumatic industry&Industrial Control Instrumentation has a strong popularity and good reputation,and provide professional customized services(Our main business is according to customer dr... Hot selling brandPacking and shipping FAQ 1.Who we are We focus on the PLC, instrument and transmitters industry, mainly selling world-famous PLC,instrument and transmitters brands2.Our advantage We have been in the industry for many years, and we have strong supply chain relationships and large inventories, with great price advantages. I will try my best to give you the best price,prove that we are sincere. 3.Our Service Purpose We want to build a long-term stable relationship, not a one-off business, to achieve a win-win goal4.Lead-Time Depending on thr model and quantity you need.So please tell us what you need now 5.Can't find the model you need? We have only shown some models,If the model you need is not found here,please contact us

× More Keyword ..

× More Menu ..

×

Manufacturing & Processing Machinery

×

Industrial Equipment & Components

×

Tools & Hardware Products